عرض: 25 50 75 100 النتائج

نتائج البحث: 25 من أصل 5,034

تثبيط التكلسات في انظمة التناضح العكسي باستخدام مواد كيمياوية == Scale Inhibition In Reverse Osmosis Systems Using Chemical Materials

اسم المؤلف: زهراء احمد عبد الامير
اسم المشرف: نجوى صابر مجيد
الموضوع العام: الهندسة الكيمياوية
السنة: 2014
الموضوع الدقيق: الهندسة الكيمياوية
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: تم في ھذا البحث دراسة تثبيط تكون تكلسات كاربونات الكالسيوم على سطح غشاء نظام تناضح عكسي باستخدام نوعين من مثبطات تكون التكلسات وھما كلوريد الزنك ومادة بوليمرية بتراكيز منخفضة ودراسة تاثير تغيير معدل جريان المحلول الداخل, حامضية المحلول الداخل, تركيز ال | The present study deals with the calcium carbonate (CaCO3) inhibition on the membrane surface of the reverse osmosis (RO) desalination system by using two types of scale inhibitors which are Zinc Chloride (ZnCl2) and Polyamino Polyether Methylene Phosphonate (PAPEMP) in low concentrations and study the effect of changing the feed solution flowrate, PH of the feed solution, concentration of the inhibition material and the type of the inhibitor used on the inhibition process. In this study a range of 10 - 25 l/h of feed solution flowrate was used, the concentration of CaCl2 was 610 mg/l, the concentration of NaHCO3 was 511 mg/l, the concentration of MgSO4 was 49 mg/l, the feed pH was in the range of 6 - 10, the operating pressure kept constant at 3 bars and the temperature washeld constant at room temperature (about 40 °C) through all experiments. The concentration of the feed solution was constant, but the concentration of the inhibitors was changed using 2, 4 and 8 mg/l of Zinc Chloride then using 8 and 15 mg/l of Polyamino Polyether Methylene Phosphonate The results showed that : Permeate rate increases as the feed flowrate increases while it decreases with time.Total dissolved solids decreases as the feed flowrate increases while it increases with time.Recovery rate decreases as the feed flowrate increases and it also decreases with time.Permeate rate, recovery rate and the total dissolved solids decreases as the inlet solution pH increases.Permeate rate and recovery rate increases while the total dissolved solids decreases when Zinc chloride or Polyamino Polyether Methylene Phosphonate was used.Permeate rate and recovery rate increases when Polyamino Polyether Methylene Phosphonate inhibitor was used more than the increment of them when Zinc chloride inhibitor was used.Total dissolved solids decreases when Zinc chloride inhibitor was used more than the diminution of them when Polyamino Polyether Methylene Phosphonate inhibitor was used.

معالجة الماء من حقول النفط باستخدام محاليل ايونية في منظومة التعويم بالهواء المذاب == Treatment of Oilfield Produced Water Using Ionic Liquids In A Dissolved Air Flotation System

اسم المؤلف: اوس عباس فاضل
اسم المشرف: سوسن عبد مسلم محمد | سعدي كاظم عبد الحسين
الموضوع العام: الهندسة الكيمياوية
السنة: 2014
الموضوع الدقيق: الهندسة الكيمياوية
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: في العراق معدل تراكيز الزيوت والشحوم (OG) في الماء المنتج يجب الا يتجاوز 09 ملغم\لتر. ولذلك فانه يتطلب معالجة المياه المنتجة بغية تلبية الحد التنظيمي للتصريف مسبقا.تم جلب نماذج الماء المنتج الخام من شركة نفط الوسط ) Md.O.C ( من الحقول النفطية من شرق بغد | In Iraq the average Oil and Grease (OG) in water concentration in discharge produced water must not exceed 10ppm. Therefore treatment of produced water is required in order to meet the pre - disposal regulatory limit.Raw produced water samples were procured from the Middle oil company (Md.O.C) (from East of Baghdad fields).Jar tests experiments were used to give a first, rough estimation for coagulants dosage of Ferric chloride and aluminum sulfate and pH values that will be used in the batch Dissolved Air Flotation (DAF) experiments. Then, the effects of the three ionic liquids (ILs) types; 1 - hexyl - 3 - methylimidazolium tetra fluoroborate (ILE), 1 - hexyl - 3 - metylimidazolium hexafluorophosphate (ILF) and 1 - octyl - 3 - methylimidazolium tetra fluoroborate (ILG) on the performance of the batch DAF unit were evaluated.It was concluded that, the beast operating conditions of the batch DAF unit were at a saturation pressure of 5 bar, recycle ratio of 50% and ambient temperature of 30 - 35 ?C. Ferric chloride with a dosage of 10 ppm was chosen as the suitable coagulant due to its low sensitivity to pH change, and its high removal efficiency for oil and turbidity in about ten minutes. ILs were used at concentration of 50 ?l per one liter of treated produced water. It was used in two positions of the DAF system; the saturation vessel and the treatment tank. The OG removal efficiency using ILG as an efficient surfactant in saturation vessel was higher than that in the treatment tank and higher than other ILs (ILG>ILF>ILE). The highest demulsification rates were obtained through saturation pressure range (2 - 5) bar. It reached about 90% removal efficiency at a pressure of 5 bar, and it was obtained 85% at saturation pressure of 3 bar which reduces the operation costs. The treated water concentration at 3bar was 9.5 ppm which meets the Iraqi pre - disposal regulatory limit.The results of testing the three ILs (ILE, ILF and ILG) in the saturation vessel and the treatment tank were used to produce contour line for the OG removal efficiency. This was conducted in order to detect the performance of the three ILs The results of optical microscope which was used to study coalescence of oil droplets in water phase, lead to consider the ILG as an effective demulsifier for Iraqi oil field produced water It was noted that the use of ILs in saturation vessel allowed micro bubble generation at operating pressures lower than 3 bar with high - energy savings.

اداء الحماية الكاثودية لخطوط الانابيب == Performance of Cathodic Protection For Pipe Lines

اسم المؤلف: انس ثائر علي
اسم المشرف: نصير عبود عيسى الحبوبي
الموضوع العام: الهندسة الكيمياوية
السنة: 2014
الموضوع الدقيق: الهندسة الكيمياوية
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: ان تاكل الهياكل المعدنية المدفونة في التربة والتي على اتصال مع التربة لفترة طويلة تعتبر مشكلة هندسية واقتصادية كبيرة.في جميع انحاء العالم هنالك الكثير من انابيب النفط والغاز والماء وكابلات الاتصالات وكذلك صهاريج التخزين والمباني والاسسات والعديد من الهيا | The corrosion of metallic structures buried in soils or in contact with soils has long been a serious engineering and economic problem. All over the world millions of kilometers of gas, water, oil pipelines, communication cables, power cables as well as storage tanks, buildings foundations, and many other structures are buried in the soil, suffering from soil corrosion problems which affect mainly the external surfaces of these structures. In many countries pipelines are by far the most important means of hydrocarbon transportation. This applies to the transport of crude, finished products and natural gas.It is an international problem with more structures and materials buried in the soil. The truly international scope of interest of this subject can be seen by the amount of literature and researches in this field. Attempts have been made to overcome this problem by the use of various types of techniques. The most common and applicable technique is cathodic protection.In this research a carbon steel pipe of length 100 cm buried in a wooden box submerged by soil and impressed current cathodic protection system (ICCP).was applied using power supply and electrical closed circuit, several important factors affecting the pipe protection from corrosion has been studied, like Anode position (distance and depth), soil resistivity (wet and dry), condition the pipe (coated and un - coated), distribution of potential and currents along the pipe(cathode) and the amount of current required to achieve cathodic protection.A correlation was achieved to simulate the ranges of parameters and factors affecting Impressed Current Cathodic Protection. Regression of this model to data and results yielded parameter values vary depending on the effect of the same factor.

ازالة الكبريت بالامتزاز من النفثا الثقيلة العراقية بواسطة 13X زيولايت == Adsorption Desulfurization of Iraqi Heavy Naphtha Using 13X Zeolite

اسم المؤلف: موفق محمد يحيى
اسم المشرف: حسين قاسم حسين
الموضوع العام: الهندسة الكيمياوية
السنة: 2014
الموضوع الدقيق: الهندسة الكيمياوية
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: اجري هذا العمل لدراسة تاثير الامتزاز الانتقائي في ازالة مركبات الكبريت من النفثا الثقيلة العراقية التي تم توريدها من مصفاة الدورة. انجزت عملية الامتزاز بواسطة 13 منخل جزيئي داخل العمود ذو الحشوة الثابتة. X 6?? - من ??5 LHSV وقد نفذ الامتزاز الانتقائي في | This work was conducted to study the effect of selective adsorption on removal of sulfur compounds from Iraqi heavy naphtha which was supplied from Al - Dura refinery. The adsorption was carried out by molecular sieve 13X in a fixed - bed column.The selective adsorption was run out at different operating conditions such as LHSV from 1.5 - 6.0 h P - 1 P , molecular sieve bed weight from 15 - 30 g , sulfur inlet concentration of feedstock from 600 - 1650 ppm, and adsorption temperature at 25 PoPC and 40 PoPC.The breakthrough time, breakpoint and saturation state ( bed replace point ) were determined for different operating conditions in addition to the ratio of accumulated effluent weight per bed weight. Also , regeneration possibility of 13X spent catalyst was studied by using oxidative technique at different temperatures and air flow rates.The results show that increasing in LHSV and inlet concentration makes the breakthrough curves more steeper , also the breakthrough time and breakpoint decreases. Increasing the bed weight will increase both the breakthrough time and breakpoint.The best operating conditions for removing sulfur compounds were LHSV 3.0 h - 1 , bed weight of molecular sieve about 20 g and 25oC temperature , where the sulfur content in a heavy naphtha was reduced from nearly 600 ppm to less than 1 ppm (by weight).Regeneration step was thermally took place by hot air flow in a range of 16.66 - 25 liter / min and temperature range from 200 - 350 oC , the best desorption conditions for (85.8%) weight percent removal were at 16.66 liter / min air flow and 350 oC.

دراسة الحركية ونمذجة تفاعل استرة حامض الاوليك باستخدام NaY زيولايت المحضر == Kinetic Study And Modeling of Olic Acid Esterification Over Prepared Nay Zeolite

اسم المؤلف: رويدة نزيه عباس
اسم المشرف: عمار صالح عباس
الموضوع العام: الهندسة الكيمياوية
السنة: 2014
الموضوع الدقيق: الهندسة الكيمياوية
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: تم تحضير زيولايت من نوع استرة حامض الاوليك. اجريت فحوصات الاشعة السينية ونسبة الصوديوم ونسبة السيليكا الى الالومينا والمساحة السطحية والحجم المسامي للعامل المساعد المحضر.اظهرت الفحوصات التوافق بين العامل المساعد المحضر مع التركيب العام للزيولايت القياسي. | The NaY zeolite catalyst was prepared from locally available Iraqi kaolin in order to use it in the esterification reaction of oleic acid. X - ray diffraction, scanning electronic microscopy, sodium content, silica to alumina ratio, surface area and pore volume were determined for the prepared NaY zeolite. The results of x - ray diffraction and scanning electron microscopy show that the prepared NaY zeolite has approximately the same crystal structure as the standard. The sodium content was 12.26 wt. %, and the silica to alumina mole ratiowas 2.6, surface area 330 m2/g and pore volume 0.35 cm3/g. Because of the oleic acid is one of the free fatty acids that can found in vegetable oils and animal fats. Oleic acid used as a suggested feedstock to study and simulate production of biodiesel via esterification reaction.Esterification reaction was analyzed at different operational conditions including the ethanol/oleic acid molar ratio of 3/1 and 6/1, different temperature from 40 to 70 °C, reaction time up to 180 minutes and catalyst (2, 5 and 10 wt. % NaY zeolite). The maximum conversion of oleic acid (about 0.83) was observed at 6/1 ethanol/oleic molar ratio, 70 °C reaction temperature, 10 wt. % NaY zeolite as a catalyst, and 60 minutes contact time. The study of the kinetics of the esterification reaction of oleic acid, indicated that the value of the activation energies of esterification ware 42692 and 17218 J/mol for forward and backward reaction respectively, and frequency factors were 7.2*104 (mol - 1/minute) for forward reaction and 4.5 (mol - 1.25/minute) for backward reaction. The values of reactants and products orders were 1, 1, 1.2 and 1 for oleic, ethanol, ester and water respectively.The statistical analysis of the esterification reaction and experimental data indicates that the average relative error was 1.53, within 0.95 confidence level.ReactOp cascade package simulator used for simulation the behavior of batch and plug flow reactors in different operating modes (adiabatic and isothermal) carried out at selected operating conditions Contents Contents.

استخدام المادة النانو مسامية SBA - 15 لازالة الملوث العضوي من المياه الصناعية == A Nanoporous SBA - 15 As Adsorbent For Removal of Organic Pollutants From Wastewater

اسم المؤلف: رغد عدنان حبش
اسم المشرف: انعام اكرم صبري | طالب محمد نايف
الموضوع العام: الهندسة الكيمياوية
السنة: 2014
الموضوع الدقيق: العمليات الصناعية
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: تم تحضير ماده السليكا النانويه المسامية (SBA - 15) باستخدام (TEOS) كمصدر للسيليكا و(P123) كقوالب ومن ثم اجريت فحوصات عليها منها حيود الاشعة السينية (XRD),المجهر الالكتروني (SEM)،المساحة السطحيه ( (BET وطيف الاشعة تحت الحمراء (FTIR). بعد ذلك تم دراسة سلو | Santa Barbara Amorphous (SBA - 15) nanoporous silica was prepared using Tetraethylorthosilicate TEOS as silica precursor, Pluronic P123 as template, and characterized by means of X - ray diffraction (XRD), scanning electron microscopy (SEM), BET surface area and fourier transform infrared (FTIR) spectroscopy. The adsorption behavior of methylene blue from synthetic wastewater onto mesoporous SBA - 15 was studied. Both batch and continuous systems were studied. Batch experiments were carried out to measure the adsorption as a function of contact time, initial concentration (15 - 110 mg/l), pH (3 - 11) and adsorbent dose (0.1 - 2.3g/l) to specify the optimum operation condition. The equilibrium of the process was achieved within 20 min. Adsorption isotherms were fitted with the Langmuir, Freundlich and Temkin models. The equilibrium data were best represented by the Langmuir isotherm model with higher correlation coefficient R2 value of (0.990). The kinetics of the MB sorption on SBA - 15 were examined by using pseudo - first and pseudo - second order kinetics models. The kinetics analysis manifested that the overall adsorption process was successfully fitted with the pseudo - second - order kinetic model. In continuous studies, the adsorption of methylene blue from synthetic wastewater onto SBA - 15 in fixed bed was investigated and breakthrough data of the dye was determined. This research is run in small scale column with an internal diameter of 0.7 cm and 35 cm height at constant temperature and pH value. The effect of bed height (3, 6, 9 cm), flow rate (0.6, 1.0,1.4 ml/min) and initial MB concentrations (40, 70, 100 mg/l) on breakthrough curves were investigated. It is found that breakthrough time increases with increasing bed height, but decreases with increasing methylene blue inlet concentration and flow rate. Thomas and Yan models were used to determine the kinetic constants and to predict the breakthrough curves. The experimental data showed a better fit to Thomas adsorption model. In order to find out the possibility of reuse SBA - 15, desorption study was also carried out in this investigation. SBA - 15 can be effectively recovered by calcinations and reused fourteenth times in batch system and five times in continuous system without significant loss in removal of methylene blue from aqueous solution. The long reuse life of SBA - 15 makes it an efficient adsorbent for removal of methylene blue from wastewater at high potential for application in industry.

عمليات التنافذ الامامي - العكسي لمعالجة المياه الملوثة بالزيوت == Forward - Reverse Osmosis Processes For Oily Wastewater Treatment

اسم المؤلف: نور حمود زغير
اسم المشرف: حسن فرهود مكي
الموضوع العام: الهندسة الكيمياوية
السنة: 2014
الموضوع الدقيق: الهندسة الكيمياوية
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: في هذه الدراسة, تم بحث مدى ملائمة عمليات التنافذ (الامامي - العكسي) لمعالجة المياه الملوثة بالزيوت. حيث طبقت عملية التنافذ الامامي لاسترجاع الماء النقي من المياه الملوثة بالزيوت. تم استخدام زيت محرك الديزل والكازولين نوع (15W - 40) لتحضير محلول اللقيم, بي | In this study, the feasibility of Forward - Reverse membrane osmosis system was investigated for treating the oily wastewater. Forward osmosis (FO) process was applied to recover pure water from oily wastewater. Gasoline and diesel engine oil (15W - 40) was used to prepare the feed solution (FS). While sodium chloride (NaCl) and magnesium chloride (MgCl2) salts were used as draw solutions, and the membrane that was used in FO process was cellulose triacetate (CTA) membrane. While reverse osmosis process was used to recovery water from the diluted draw solution using polyamide (thin film composite (TFC)) membrane. In the first stage was applying the FO process for treating the oily wastewater with two parts. The first part included the FO process using the batch system whereas the second part included the FO process using the flowing system for different draw solutions. Theoperating parameters studied were : draw solution type, draw solution concentrations (0.25 - 0.75 M), oil concentration in FS (100 - 1000 ppm), the temperatures of FS and DS (30 - 45 °C), pH of FS (4 - 10) and for the forward osmosis flowing process the flow rate of both DS and FS (20 - 60 l/h), while the pressure was maintained at 0.5 bar. The run - time of the FO process was for five hours. It was found that water flux through membrane decreases with increasing time, while oil concentration in the FS increases with increasing time. Also, it was found that the water flux produced from the osmosis cell and oil concentration in FS increase by increasing the concentration of draw solutions, the flow rate of FS and the temperature for a limit (40oC), then, the water flux and oil concentration decrease with increasing the temperature because of happening the internal concentration polarization phenomenon. By increasing the oil concentration in FS and the flow rate of the DS, the water flux and oil concentration in FS were decreased. While it had a fluctuated behavior with increasing the pH of oily wastewater. It was found also that MgCl2 gives water flux higher than NaCl. It was observed that the best operating conditions in this study were : concentration of salt (0.75 M) for MgCl2, oil concentration (100 ppm), pH of FS (7.3), temperature of feed and draw solution (40oC), flow rate of FS (60 l/h), and flow rate of DS (20 l/h). The values of resistance to solute diffusion within the membrane porous support layer were 55.93 h/m and 26.21 h/m for NaCl and MgCl2 respectively. The second stage was applied reverse osmosis process for separating the fresh water from a diluted (NaCl) solution using different parameters such as draw solution concentration (0.08 - 0.16 M), feed flow rate (20 - 40 l/h) within two hours of work of the reverse osmosis system.

تاثير المحتوى المائي، درجة الحرارة وكلوريد الصوديوم على تاكل CO2 للصلب الكربوني (A106 B) في النفط العراقي == Effect of Water Content , Temperature And NaCl on CO2 Corrosion of C - Steel (A 106 B) in Iraqi Crude Oil

اسم المؤلف: انعام يوسف عبد الرحمن
اسم المشرف: سعد احمد جعفر
الموضوع العام: الهندسة الكيمياوية
السنة: 2014
الموضوع الدقيق: الهندسة الكيمياوية
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: صلاح الدين
الصفحات الاولى:
المستخلص: ان التاكل الداخلي في انابيب الصلب الكربوني الذي يحدث بوجود غاز ثاني اوكسيد الكربون يعتبر مشكلة جوهرية في صناعات النفط والغاز وهو يقترن دائما مع وجود الماء. ان احتمالية حدوث التاكل تزداد بصورة عامة مع تزايد نسبة الماء ومع زيادة مستوى الماء المنتج تزداد مع | Internal corrosion of carbon steel pipelines occurring in the presence of CO2 is a substantial problem in the oil and gas industries. It is always associated with the presence of free water. The likelihood of corrosion generally increases with the volume fraction of the water phase. As the produced water level increases, the corrosion rates of carbon steel increase very rapidly and causes damage of petroleum and gas pipelines. The present research work focuses on the investigating of the corrosion rate of carbon steel as flow line in crude oil production with CO2 content employing three Iraqi crude oil (Kirkuk crude oil, Halfaya crude oil, Rumalia crude oil) with different brine concentrations [1%NaCl, 2%NaCl, 3%NaCl]. Determining the corrosivity of Iraqi crude oil was studied for the first time. Experiments were performed in an autoclave test apparatus, crude oil - produced water mixtures, water cuts were (0, 10, 20, 30, 40, and 100%), and total volume of mixtures inside the autoclave was always kept at 100ml and temperature (20, 40, 60°C). For all experiments, CO2 partial pressure was maintained at (4 bar) and rotational speed (500 rpm).The corrosion rates were determined by the weight loss technique. The results revealed that the corrosion rates of carbon steel increased by increasing water cut and temperature, but decreases with increasing salt concentration for all types of crude oil. Results also indicated that different crude oil has significantly different effects on corrosion of carbon steel, with identical brine compositions. Therefore, Rumaila crude oil exhibits the highest corrosion rates and Kirkuk crude oil exhibits the lowest corrosion rates while Halfaya crude oil exhibits a moderate corrosion rates e.g. at 1% NaCl, 20% water cut, temperature 60°C, pressure 4bar, the corrosion rate of carbon steel in Rumaila crude oil is 0.9163mm/yr whereas it is 0.564 mm/yr and 0.705 mm/yr in Kirkuk crude oil and Halfaya crude oil respectively. The Corrosion Rate Break produced water level was determined from the experiments. These tests are employed to evaluate the requirements for corrosion inhibitor treatment. At 100% water cut (brine/CO2) the corrosion rates of carbon steel was the highest. The presence of crude oil decreases the corrosion rates e.g. at 1% NaCl,100% water cut(brine/CO2) the corrosion rate is 7.1197 mm/yr, whereas at 40% water cut/ Rumaila crude oil the corrosion rate is 1.4097 mm/yr.

محاكاة لمعمل الاثلين في العراق باستخدام الاسبن بلسن والماتلاب == Simulation of Iraqi Ethylene Plant Using Aspen Plus And Matlab

اسم المؤلف: هدى عامر عبد القادر
اسم المشرف: صفاء الدين عبد الله النعيمي | زيدون محسن شكور
الموضوع العام: الهندسة الكيمياوية
السنة: 2014
الموضوع الدقيق: العمليات الكيمياوية
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: يعد معمل الاثيلين واحد من اهم معامل البتروكيماويات والاكبر حجما في العالم في الوقت الحاضر. بالاضافة الى ذلك، فانه يعتبر جوهر اي مجمع للبتروكيماويات. وفي مثل هذه المعامل، يخضع الغاز الطبيعي الى العديد من العمليات لفصل مكوناته.الهدف من هذه الدر | Ethylene plant is one of the most important and largest volume petrochemicals in the world today. In addition, it is a core of any petrochemical complex. In such plant, the natural gas is subjected to many processes to separate the components. The objective of this study is to develop a detailed model to simulate an ethylene plant, which includes a pyrolysis section, a separation system and an integrated refrigeration system. An optimization has been performed for a part of the plant; this part is the furnace.The ethylene plant at the Petrochemical Complex in PC1 - Basrah has been considered as a case of study. The kinetics of ethane thermal cracking in pyrolysis furnace has been simulated using Aspen Plus and MATLAB. The radiant coils in furnace have been modeled as a one dimensional plug - flow reactor in which ethane is subjected to steam cracking. The overall plant has been simulated using Aspen Plus version (7.3), and the reactor has been simulated using MATLAB environment, version (2013a) in addition to Aspen Plus. The validity simulation model test has been achieved by comparing the simulation results with the actual data collected from PC1and it showed a great similarity and reliability for both simulation models.A steady state simulation model has been developed to study the behavior of multi - types feed supplied to the plant. Furthermore, the model has been used to evaluate the effects of various process parameters, including temperature of reaction (Reactor outlet temperature), dilution steam to ethane ratio (DS/HC) and the outlet flow rate of hydrocarbons.The other aim of this study is to obtain the optimum operating conditions using Aspen Plus for the reactor in the furnace which has an effect on the final product to determine the maximum profit. Optimization using Genetic Algorithm (GA) by MATLAB has been used as well as Aspen Plus, and a comparison has been made between both methods. The selection of the optimum operating conditions of reactor was obtained to achieve the following objectives together : • Increasing the production rate of ethylene.• Increasing the outlet flow rate of hydrocarbons.These objectives have managed to be achieved all together by maximizing the total profit obtained from the furnace. Finally, Aspen Plus results show that the objectives have been satisfied by manipulating the decision variables Temperature of reaction (Reactor outlet temperature) in the range of (850 - 920) ?C, dilution steam to ethane ratio DS/HC in the range of (0.2 - 0.5) and the outlet flow rate of hydrocarbons ) in the range of (2421 - 1064) Kmole/hr to increase the profit of the furnace to approximately (10.541%) and (5.55%) for the whole plant.

معالجة واستصلاح الماء المصاحب للنفط العراقي باستخدام طريقة عمود التطويف وتقنية الاغشية == Treatment And Reclaiming of Iraqi Oil Field Produced Water By Flotation Column And Membrane Technology

اسم المؤلف: هدى كاظم حسن
اسم المشرف: ثامر جاسم محمد | قصي فاضل عبد الحميد
الموضوع العام: الهندسة الكيمياوية
السنة: 2014
الموضوع الدقيق: العمليات الكيمياوية
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: يتم انتاج كميات كبيره من الماء المصاحب النفطي من قبل شركة نفط الجنوب.يعتبر محتوى النفطي oil - water والاملاح الذائبه TDS من اخطر الملوثات والتي تتم معالجتها باحدث التكنلوجيا في السنوات الاخيره تم استخدام تقنية الاغشية لمعالجة الماء المصاحب النفطي.الهدف م | A large amount of oil field produced water is generated by South Oil Company. Oil - in - Water and TDS are the most serious pollutants for which current treatment technologies are often costly and ineffective in order to reuse water. In recent years, membrane process has been applied for produced water treatment.The aim of the present work is to treat produced water from oil well before being disposed in environment or reused as re - injection to oil well or agriculture water. Oil field produced water is very difficult wastewater to treat and its characteristics change as well to well. The sample test of this study was taken from dehydrator in the DSI/North Rumila/Southern Oil Company in Basrah /Iraq. The treatment process of produced water consists of two stages. The first stage as pre - treatment is achieved by continuous dissolved air flotation (DAF) to reduce the oil content. The second stages, as advanced treatment processes, are accomplished by microfiltration (MF) to reduce the turbidity and nanofiltration (NF) to reduce the salt content as TDS of produced water. The experimental work was carried out using dissolved flotation column is of Perspex glass (0.1 m I.D, 1.5 m height). The bottom of the column connected to a conical joint of QVF glass with a Teflon distributer. The effect of operating parameters (flow rate of produced water, pH, initial oil concentration, flotation time, alum dosage and surfactant of SLS) saturated pressure=5 Atm on the oil content or oil removal efficiency was investigated. The results showed that the oil removal efficiency increases with increasing the flow rate of produced water, the flotation time and coagulants dosage. The oil removal efficiency in DAF unit without coagulants is equal to (80, 94, 95%) for initial oil concentration (30, 50, 70 ppm), respectively at a flow rate 0.03 m3/h and pH=6. While flotation with coagulation, the results indicated that the removal efficiency is equal to 94% (residual oil content <10 ppm) at pH=5, alum dosage=560 ppm, and initial oil concentration=50 ppm, and the removal efficiency is equal to 89.6 at pH=6, alum+SLS dosage=80 ppm, and initial oil concentration=50 ppm. The kinetics of flotation column was studied and it was found that the order of the reaction is changing between zero to first order.The treatment of produced water by membrane technique was carried out by cross flow mode in hallow fiber microfiltration (MF) and nanofiltration (NF). The effect of operating parameter such as transmembrane pressure (TMP) (1, 1.5, 2 bars) with cross flow 20 mL/min, at room temperature, on the flux, rejection, and turbidity and TDS removal was studied. The experimental results by MF manifested that the permeation flux is (108, 156, 611 l/m2.h) and transemembrane pressure is 2 bar at initial turbidity (100, 200, 300 NTU), respectively. But NF, as a final treatment of produced water to reuse, was studied at different feed concentrations (82950, 75050, 67150 ppm) with different TMPS. According to the experimental results, the higher permeation of flux =15 (l/m2.h) at 82950 ppm and 2 bar, was obtained.The experimental results of the removal efficiency were represented in two and three dimensional graphs. An empirical correlation for R% as a function of different parameters (flow rate, pH, and oil concentration) was developed by aided computer using the following formula %R= a + c1*x1n1 + c2*x2n2 + c3*x3n3.

انتقال الحرارة في الغليان الحوضي باستخدام موائع النانو == Pool Boiling Heat Transfer Using Nanofluids

اسم المؤلف: خيرية مطر عيسى الخزاعي
اسم المشرف: جمال مانع علي الربيعي
الموضوع العام: الهندسة الكيمياوية
السنة: 2014
الموضوع الدقيق: الهندسة الكيمياوية
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: يمكن اعتبار نظام المغلي التنوي واحدة من اكثر الطرق فعالية لزيادة التبادل الحراري في منطقة صغيرة نسبيا. انتقال الحرارة في الغليان الحوضي لموائع النانو تم التحقق عنها تجريبيا باستخدام مياه الالومينا AL2O3 ومياه ثاني اوكسيد التيتانيوم TiO2.كموائع نانويه (n | Nucleate boiling regime can be considered one of most effective ways to increase the heat exchange in a relatively small area. Pool boiling heat transfer nanofluid was investigated experimentally using Al2O3 - water and TiO2 - water nanofluids. The experimental test rig consists of boiling vessel and electrically heated plate heating element of stainless steel as heating element. Different concentrations of nanofluids were tested (0.05w %, 0.1w %, 0.3 w%, and 0.5 w %). The nanofluids for Al2O3 and TiO2 were prepared by mixing the( Al2O3 and TiO2) nanoparticles with distilled water in magnetic stirrer for three time periods at (2, 3 and 4) hours and for 1 hour in an ultrasonic bath to suspend the nanoparticles in base fluid. The nanofluids were scanned by scanning electron microscope to ensure well dispersion of nanoparticles in distilled water. Experiments were carried out firstly using pure water then nanofluid to compare the heat transfer enhancement. Results give maximum enhancement ratio in heat transfer rate of (100%) for 0.5% weight concentration for Al2O3 - water nanofluid and (81.82%) for TiO2 - water nanofluid at the same concentration. In both nanofluids the enhancement ratio increases with increased nanoparticle concentrations.This lead to increase in pool boiling heat transfer coefficient.

ازالة الكبريت من زيت الوقود باستخدام الاكسدة المعززة بالموجات الفوق الصوتية == Ultrasound - Assisted Oxidative Desulfurization of Fuel Oil

اسم المؤلف: جعفر مازن جعفر
اسم المشرف: نيران خليل ابراهيم | ولاء عبد الهادي نوري
الموضوع العام: الهندسة الكيمياوية
السنة: 2014
الموضوع الدقيق: الهندسة الكيمياوية
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: Due to the dramatic environmental impact of sulfur emissions associated with the exhaust of engines, sulfur content specification for diesel fuels became more and more stringent worldwide. Last environmental regulations for ultralow sulfur diesel require very deep desulfurization processing, which cannot be met by the conventional hydrodesulfurization process (HDS).The present work focuses on benefiting from integrating an ultrasoundassisted oxidative desulfurization process (UAODS) with the conventional HDS process to produce ultra - low sulfur fuels. The proposed method involves a batch ultrasound - assisted oxidative desulfurization process to desulfurize a previously hydrotreated diesel containing 480 ppm sulfur. The oxidizing system used was H2O2/CH3COOH with FeSO4 being used as a catalyst. An ultrasonic probe system was used to enhance the conversion of sulfur - bearing compounds that exist in diesel to sulfones and sulfoxides to affect their removal by a certain separation method, such as extraction or adsorption.The major influential parameters related to UAODS process have been investigated, namely : ratio of oxidant/fuel, ratio of the promoter/oxidant, dose of catalyst, reaction temperature, intensity of ultrasonic waves. A set of comparative studies were also carried out including type of extraction solvent, effect of initial sulfur content, and type of sulfur separation method. Total evaluation for the treated diesel was performed, including GC - MS analysis which has been used to monitor the change of organic sulfur compounds andhydrocarbons in diesel during the desulfurization process.The oxidation treatment, in combination with ultrasonic irradiation, revealed a synergistic effect for diesel desulfurization. The experimental results showed that the removal efficiency for sulfur compounds could amount to 98%, and sulfur level can be reduced to 12 ppm at mild operating conditions (70 and 1 bar). This indicates that this process is so efficient and promising for the production of ultra - low sulfur diesel fuels.The kinetics of the reaction has been also studied. It was observed that the UAODS of diesel fuels fitted pseudo - first - order kinetics under the studied experimental conditions. During this process, values of the apparent rate constant and activation energy were 0.373 min - 1 and 24 kJ/mol, respectively.

ازالة المحتوى الكبريتي من وقود الديزل بواسطة الاكسدة والاستخلاص بالمذيب == Desulfurization of Diesel Fuel By Oxidation And Solvent Extraction

اسم المؤلف: شيم بهجت عبد الكريم
اسم المشرف: ودود طاهر محمد | رغد فريد
الموضوع العام: الهندسة الكيمياوية
السنة: 2014
الموضوع الدقيق: الهندسة الكيمياوية
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: يهدف البحث الى ازالة المحتوى الكبريتي من مقطع الديزل المهدرج للتخلص من المركبات الكبريتية الثايوفينية التي تتعذر ازالتها بواسطة عملية الهدرجة المعتمدة في المصافي النفطية. ودراسة افضل الظروف للحصول على اعلى نسبة ازالة.رست الظروف التشغيلية التالية : سرعة ال | Removal of sulfur species from fuels is an increasingly critical environmental issue. Hydrodesulfurization (HDS) removes sulfur compounds, such as mercaptans and sulfides from hydrocarbons; however, some sulfur - containing compounds (such as diebenzothiophene) are very difficult to remove and need deep desulfurization processes.This work was applied to the desulfurized diesel fuel produced from the conventional HDS process for ultra - desulfurization. The used fuel types in this investigation were either real diesel fuel or simulated diesel fuel, where sulfur - containing compound ( dibenzothiophene DBT) converted to its corresponding sulfone by oxidation using hydrogen peroxide as an oxidant and acetic acid as homogenous catalyst, and solvent extraction by using acetonitrile (ACN) or N - methyl - 2 - pyrrolidone (NMP) as extractants.Simulated diesel fuel according to British Petroleum 200B doped with dibenzothiophene (DBT) was prepared, the effect of stirring speed (150, 250, 350 and 450) rpm, temperature (30, 40, 45 and 50) ?C, oxidant/simulated diesel fuel ratio (0.5, 0.75,1 and 1.5) (v/v), catalyst/oxidant ratio (0.125, 0.25, 0.5 and 0.75) (v/v), solvent type, and solvent/simulated diesel fuel ratio (0.5, 0.6, 0.75 and 1) (v/v) were examined in order to obtain the maximum sulfur removal. The results of this work exhibit that the highest removal of sulfur 98.5% for N - methyl - 2 - pyrrolidone and 95.8% for acetonitrile were obtained under the conditions of operating in table below : Stirring Speed (rpm) 350 Temperature (?C) 50 Oxidant (hydrogen peroxide)/simulated diesel fuel ratio 1 Catalyst (acetic acid)/oxidant ratio 0.5 Solvent (ACN or NMP)/simulated diesel fuel ratio 1 Experiments with the above best conditions were carried out on Real diesel fuel obtained from Al - Dora refinery with 1000 ppm sulfur containing compounds. It was found that sulfur removal from real diesel fuel was 62.5% for acetonitrile and 75% for N - methyl - 2 - pyrrolidone.

تطبيقات الطرق العددية في التاكل الكلفاني للمعادن المزدوجة == Applications of Numerical Methods In Galvanic Corrosion of Coupled Metals

اسم المؤلف: بسمة محمد كاظم الشاهر
اسم المشرف: جمال مانع علي الربيعي
الموضوع العام: الهندسة الكيمياوية
السنة: 2014
الموضوع الدقيق: العمليات الصناعية
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: تم دراسة سلوك تاكل معادن النحاس والكربون الصلب والزنك في تراكيز مختلفة من حامض الهيدروكلوريكHCl) ) (0.025، 0.05 و0.075 مولاري ) عند درجات حرارة مختلفة (30، 40 و50 درجة مئوية) باستخدام القياسات الكهروكيميائية (Electrochemical Measurements) في حالة المعا | The corrosion behaviors of metals Copper, Carbon Steel and Zinc in a different concentrations of HCl acid (0.025, 0.05 and 0.075M) at different temperatures (30, 40 and 50°C) were investigated using electrochemical measurements in couple and single state.The galvanic behaviors of coupled metals (Cu - Fe),( Cu - Zn) and (Fe - Zn)were studied using Zero Resistance Ammeter (ZRA) technique, it has been used to measure the galvanic current (Ig) and galvanic potential (Eg) with time. The galvanic corrosion cells for all couples have equal areas of anode and cathode (2×2cm).The galvanic current density (ig) is increased with increasing solution concentration and temperature. The galvanic potential (Eg) is shifted to less negative with increasing solution concentration and temperature and it is close to the corrosion potential of the anode in the couple conditions.The potentiostatic polarization behavior of single three metals (Copper, Carbon Steel and Zinc) in different concentrations of dilute HCl acid (0.025, 0.05 and 0.075M) at temperature (40°C) is found under activation control. The corrosion current density is increases with increasing solution concentration and gives the following arrangement of metals : Cu> Fe > Zn A numerical analysis of galvanic corrosion was presented. The analysis was based on three numerical methods as the boundary element method (BEM), the finite element method (FEM) and the finite difference method (FDM).The potential and current density distributions on the galvanic elements are described by the Laplace equation. The Laplace equation was solved numerically, to determine the potential, current density, and corrosion caused by the galvanic cell using designed computer programs in MATLAB R2014a. The experimentally determined polarization curves have been used in order to define the nonlinear boundary conditions. This boundary value problem has been solved using Newton - Raphson iterative numerical procedure. For the three couple systems (Cu - Fe, Fe - Zn and Cu - Zn), the results obtained for galvanic potential and current density, using the numerical methods (BEM, FEM and FDM) with the overall deviations are 6.689, 10.818 and 18.846 respectively for galvanic current density and 0.631, 1.210 and 1.787 respectively for galvanic potential. From these results it can conclude that the galvanic current density and galvanic potential distribution calculated from the BEM model was in good agreement with the experimental measurements. These are because the main advantages of the BEM over the Finite Element Method (FEM) and the finite difference method (FDM) are high accuracy, discretization on the boundary only which results in a very small number of unknowns, easy dealing with non - regular boundaries and openings that only the domain boundary of interest is required to be discrete, also BEM needs fewer equations and a smaller matrix size than FEM and can solve both finite and infinite domain problems.

استخلاص الزيوت العطرية من قشور الحمضيات باستعمال التقطير البخاري بمساعدة المايكرويف == Extraction of Essential Oils From Citrus By - Products Using Microwave Steam Distillation

اسم المؤلف: سارة جبير صالح
اسم المشرف: ابتهال كريم شاكر
الموضوع العام: الهندسة الكيمياوية
السنة: 2014
الموضوع الدقيق: الهندسة الكيمياوية
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: يهدف هذا البحث الى استخلاص الزيت العطري من ثلاثة انواع من قشور الحمضيات (البرتقال, الليمون, اللالنكي) بطريقتين : التقطير البخاري والتقطير البخاري بمساعدة المايكرويف.ودراسة تاثير عوامل الاستخلاص : (وزن القشور, وقت الاستخلاص,طاقة المايكرويف ونوع قشور الحمضي | The main objectives of this research is to extract essential oil from : orange( citrus sinensis), lemon( citrus limon) and mandarin( citrus reticulata) peels by two methods : steam distillation (SD) and microwave assisted steam distillation (MASD), study the effect of extraction conditions : weight of the sample( 398.56g, 281.8g, 116.76g), extraction time, microwave power( 135W, 265W, 445W) and citrus peel type( orange, lemon, mandarin) on oil yield and compare the results of the two methods, the resulting essential oil was analyzed by Gas Chromatography (GC).Essential oils are highly concentrated substances used for their flavor and therapeutic or odoriferous properties, in a wide selection of products such as foods, medicines and cosmetics. Extraction of essential oil is one of the most time and effort consuming process. Microwave - assisted extraction is a green technique for the extraction of natural products. (MASD) was better than (SD) in terms of rapidity, energy saving and yield. (MASD) gave higher yield than (SD) with shorter extraction time, yield of orange oil extracted by (MASD) was (1.150%) in (35min.) compared to (1.095%) in (45min.) by (SD) process, same results obtained for lemon and mandarin. It was found that the optimal microwave power was (135W) and the yield was : (1.150%, 1.115%, 0.940%) for orange, lemon and mandarin respectively, (MASD) increased extraction temperature in short time and to a higher level compared to (SD).It was found that the optimal weight was (398.56g) and the yield in (SD) was : (1.095%) and MASD (1.091%) for orange oil, same results obtained for lemon and mandarin.The best citrus peel type which gave the highest yield was orange followed by lemon then mandarin in both processes.Limonene is the most abundant component in citrus essential oil, (GC) analysis showed that the amount of limonene increased in low microwave power with long extraction time for mandarin oil it was (84.3891% at 135W in 60min.), while for (SD) it was (83.0271% in 75min.) and decreased with increasing microwave power for orange oil it was (80.9661% at 265W in 35min.) while for (SD) it was (83.2189% in 45min.), (SD) was more convenient to give high amount of limonene because of the graduate temperature rise, while in microwave extraction exposure to low microwave power for long time would give complete recovery and better quality of essential oil.

تاثير الحماية من التاكل بواسطة الليزر على سبائك الالمنيوم == The Effect of Laser Surface Melting Corrosion Protection On Al Alloys

اسم المؤلف: هبة خميس اسماعيل
اسم المشرف: شذى احمد سامح
الموضوع العام: الهندسة الكيمياوية
السنة: 2014
الموضوع الدقيق: الهندسة الكيمياوية
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: يهدف هذا البحث الى دراسة تاثير المعاملة بالليزر على تاكل سبائك الالومنيوم (7075, 6061, 5083) المغمورة في محلول ملحي (كلوريد الصوديوم) بمختلف التراكيز. وقد تم اعداد عينات من سبائك الالومنيوم ذات ابعاد (2 ملم) سمك وقطر (25 ملم)، وكانت تجارب الاستقطاب في مح | The objectives of the present project are to generate uniform melted layers, free of large second phases to assess the corrosion resistance of the laser treated surface in comparison with the untreated alloy. So disc samples of (7075, 6061 and 5083) aluminum alloys of 2 mm thickness and 25 mm diameter, have been prepared. Polarization tests were carried out in (M lab potentiostat / galvanostat) (Germany) at 298K temperature and (1.5, 2.5 and 3.5) % wt of NaCl solution. The experiments were carried out before and after laser surface melting by (Nd : YAG, MED - 810) pulse laser, system (Q - Switched Nd : YAG 1064/532nm). Before laser surface melting the results showed that the value of the corrosion current density obviously increases with increasing the concentration of NaCl from 1.5% to 3.5%. As well as higher Cl - ions concentration more negative pitting potential (Epit) of aluminum alloys and decrease in the electrochemical stability of aluminum. The corrosion rate for the specimen 7075 is larger than that of 6061 and 5083 aluminum alloys under the same conditions. So it means that the specimens 6061 and 5083 have high resistance to corrosion in NaCl solution After laser surface melting the results showed that the surface of aluminum alloys became more homogenous and pure after treatment.It was found that the corrosion current density decreases after Laser Surface melting at about three orders than that of untreated samples, therefore, the value of the corrosion rate of laser - treated alloy is smaller than that of the untreated. As well as the pitting corrosion potential after Laser Surface melting obviously shifted to more positive direction for all aluminum alloys in different concentrations of the NaCl solution.

تطبيق اللابفيو والخوارزمية الوراثية في السيطرة على مبادل حراري من نوع الصفائح == Application of LabVIEW And Genetic Algorithm For Controlling of Plate Heat Exchanger

اسم المؤلف: ايمن فوزي زوين
اسم المشرف: زيدون محسن شكور
الموضوع العام: الهندسة الكيمياوية
السنة: 2014
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: تم دراسة السلوك الديناميكي لمبادل حراري من نوع الصفائح ( يتكون من 24 صفيحة ) والسيطرة عليه. الموديل النظري للمبادل طور بالاستناد على الموازنة الحرارية لصفائح المبادل.نتائج الموديل توضح السلوك الديناميكي للمبادل حيث تبين انه من الدرجة الاولى بالتقديم ((le | In this work the dynamic behavior of a plate heat exchanger (PHE) (consists of 24 plates) both experimentally and theoretically and the control of the system were studied. A theoretical model for the plate heat exchanger was developed based on the heat balance. A step change is carried in the hot water flow which is considered as a manipulated variable.The results of plate heat exchanger (PHE) showed that the dynamic behavior of plate heat exchanger in this work is dynamically as a first order lead and second order overdamped lag with a significant delay time as shown below : G(p)=(T ?_co (s))/(m ?_h (s) )= ((0.2645s+1.411) e^( - 5.63s))/(0.2156s^2+12.34s+1) The experimental heat transfer measurements of the plate heat exchanger (PHE) indicated that the overall heat transfer coefficient (U) is related to the water flow rate (m) by a correlation having the form : U = 10637 m0.7307 To verify the presented model, temperature control was applied theoretically and experimentally to the plate heat exchanger using conventional P, PI and PID controllers with tuning of control parameters by different methods; Ziegler - Nichols, Cohen - Coon and genetic algorithm to find the best values of proportional gain (Kc), integral time (?I) and derivative time (?D). The time domain specifications like rise time, settling time, overshoot and the performance indices, Integral Squared Error (ISE) and Integrated Time - Weighted Absolute Error (ITAE) were used to evaluate the performance of different control strategies. The PID controller gave better control results of temperature than other controllers, while Ziegler - Nichols tuning method gave better control results than Cohen - Coon. GA technique is the best method in simulation by compare with Cohen - Coon and Ziegler - Nichols methods. Therefore, GA method is suitable as best technique for systems which have shorter constant time.Cohen - Coon and Ziegler - Nichols methods were used in the experimental work to calculate the controller parameters, while GA method was not used in this stage.

تحضير الكاربون المنشط من نوى التمر باستخدام كاربونات البوتاسيوم كعامل منشط في ازالة صبغة المثيلين الزرقاء == Preparation of Activated Carbon From Date Stones By K2Co3 Activation For Methylene Blue Dye Adsorption

اسم المؤلف: اسماء فاضل عباس
اسم المشرف: مثنى جبار احمد
الموضوع العام: الهندسة الكيمياوية
السنة: 2014
الموضوع الدقيق: الهندسة الكيمياوية
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: Present study deals with the preparation of activated carbon (AC) from date stones by K2CO3 activation via microwave heating and the removal of methylene blue (MB) dye from aqueous solution by using such carbon as adsorbent. The influence of radiation time (4 - 12min), radiation power (540 - 700W) and impregnation ratio (0.5 - 2.5g/g) on the yield and MB uptake of such carbons were studied. Central composite design was used to determine the optimum preparation conditions and two quadratic models were developed to correlate the preparation variables for both responses.The optimum preparation conditions were reported as 8 min radiation time, 660 W radiation power and 1.5 g/g impregnation ratio resulting in 19.99% yield and 460.123 mg/g MB uptake. From the analysis of variance (ANOVA), it was found that the radiation time had the greatest effect on the yield while impregnation ratio had the greatest effect on MB uptake.The characteristics of AC were examined by pore structure analysis, scanning electron microscopy (SEM) and Fourier transforms infrared spectroscopy (FTIR). The BET surface area and total pore volume were indentified to be 1144.25 m²/g and 0.656 m³/g, respectively. Batch adsorption study was adopted to determine the experimental adsorption isotherm data of different initial concentration of MB (50 - 450 mg/l). The equilibrium data were analyzed using Langmuir, Freundlich and Sips isotherm models. The results showed that the experimental data were well fitted with sips isotherm with maximum monolayer adsorption capacity of 484.7 mg/g. Pseudo - First order, Pseudo - Second order, and intraparticle diffusion models were used to analyze experimental kinetics data with high correlation coefficient for Pseudo - second - order model.

تصميم تناسلي تكاملي تفاضلي مضبب للسيطرة على منظومة روبرت ذات ذراع مفرد متصل بمفصل مرن باستخدام تقنية البوابات المبرمجة == Design of A Fuzzy - PID Controller For Single Link Flexible Joint Robot Using FPGA

اسم المؤلف: حسين عظيم عباس
اسم المشرف: اخلاص حميد كرم | اقبال حسين علي
الموضوع العام: هندسة الحاسبات
السنة: 2014
الموضوع الدقيق: هندسة الحاسبات
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: اثناء هذا العمل ستتم مناقشة مشكلة وجود المرونة في مفصل منظومة روبوت ذات ذراع مفرد متصل بمفصل مرن، حيث ان وجوده يسبب نمط من التذبذبات الغير مرغوب بها في استجابة النظام، والتي قد تؤدي الى تدهور اداء النظام وعدم استقرار الاستجابة. ايضا تم اقتراح استخدام مسي | In this work, we have discussed the joint flexibility that exists in a single link flexible joint robotic system which causes poorly damped oscillations thatmay degrade system performance. A fuzzy - PID (Proportional, Integral, Derivative) controller hav

تحسين اداء بروتوكول لشبكات الاستشعار اللاسلكية اللاارادية == Performance Enhancement of Routiing Protocol For Autonomic Wireless Sensor Networks

اسم المؤلف: سرى فوزي اسماعيل
اسم المشرف: فراس علي صابر
الموضوع العام: هندسة الحاسبات
السنة: 2014
الموضوع الدقيق: هندسة الحاسبات
الدرجة: ماجستير
الجامعة: جامعة بغداد
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:

ملاحة وتجنب العوائق للربوت المتنقل مبنية على اساس المنطق الضبابي == Fuzzy Based Obstacle Avoidance And Navigation of Mobile Robot

اسم المؤلف: عبد الكريم عبد الهادي عبد الكريم
الموضوع العام: هندسة الحاسبات
السنة: 2014
الموضوع الدقيق: هندسة الحاسبات
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: البصرة
الصفحات الاولى:
المستخلص: هناك جانبان لهذه الاطروحة الجانب الاول هو الجانب النظري الذي يتضمن تصميم مسيطر المنطق الضبابي للسيطرة على حركة الروبوت المتنقل. تم استخدام خوارزمية سرب الجسيمات الامثل (Particle Swarm Optimization) لتحسين مسيطر المنطق الضبابي حيث استخدمت لضبط دوال الانتما | Two aspects are considered in this thesis, the first one is theoretical aspect which consist of the design of fuzzy logic controller to control the motion of mobile robot. Particles Swarm Optimization (PSO) algorithm is used to optimize the fuzzy logic co

مصادقة الرسائل وتشفير رسالة سمز لتطبيق الروبوت == Message Authentication And Encryption of Sms Message For Android Application

اسم المؤلف: فاطمة اسعد حسن الحبوبي
اسم المشرف: Shaimaa Hameed | Hassan A. Jeiad
الموضوع العام: هندسة الحاسبات
السنة: 2014
الموضوع الدقيق: هندسة الحاسبات
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: The Short Message Service (SMS) is a text based service provided by Global System for Mobile communications (GSM). SMS is one of the most widely, simple and cost effective means for communication between two persons or a group of them.In this thesis a se

تصميم وبناء نظام مراقبة الكتروني للعناية الصحية == Design And Lmplementation of Monitoring System For EHealTh Care Applications

اسم المؤلف: عبد الله علي جواد
اسم المشرف: محمد نجم عبد الله
الموضوع العام: هندسة الحاسبات
السنة: 2014
الموضوع الدقيق: هندسة الحاسبات
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: اصبح نظام مراقبة الصحة الالكترونية جزء ا مھم ا من الحياة اليومية في السنوات الاخيرة. ان التطور الحاصل في الھواتف المحمولة وغيرھا من الاجھزة المحمولة اعطى نظام مراقبة الصحة الالكتروني امكانية استخدام انواع مختلفة من الشبكات. ان نظام مراقبة الصحة الالكترو | E - Health Monitoring Systems (EHMS) have become very important part of our life in recent years. The development of mobile phones and other handheld devices have given the ability to EHMS for using different types of networks. The EHMS consists of many s

تقنيات الاستنباط للبيانات المكانية باستخدام المحلل الجيواحصائي في نظم المعلومات الجغرافية == Interpolation Techniques of Spatial Data Using Geostatistical Analyst In GIS

اسم المؤلف: غصون عيدان عرب ناصر
اسم المشرف: صالح مهدي القرعاوي | حسين زيدان علي
الموضوع العام: هندسة الحاسبات
السنة: 2014
الموضوع الدقيق: هندسة الحاسبات
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: لقد اصبحت التغييرات المناخية في البيئة العالمية مصدر قلق في جميع انحاء العالم في السنوات الاخيرة.وبما ان هطول الامطار يعتبر عاملا مناخيا مهما، فان دراسة انماطه الزمانية والمكانية مهم بالنسبة للباحثين الذين يعملون في العديد من المجالات المتفاعلة في اطار ب | Global environment change has become a worldwide concern in recent years. Rainfall is an important climatological parameter, which is useful for researchers working in many disciplines. In this thesis, spatial interpolation techniques were implemented in

تصميم وتنفيذ نظام لاسلكي لمراقبة درجة الحرارة باستخدام الزيجبي ZigBee == Design And Implementation of A Wireless Temperature Monitoring System Using Zigbee

اسم المؤلف: علي حمید توفیق محسن
الموضوع العام: هندسة الحاسبات
السنة: 2014
الموضوع الدقيق: هندسة الحاسبات
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: شبكة الاستشعار اللاسلكية (WSN) ھي عبارة عن مجموعة من العقد يتم تنظيمھا في شبكة تعاونية. لدى كل عقدة في تلك الشبكة قدرة على المعالجة، وتحتوي على ذاكرة، ولديھا جھاز ارسال واستقبال لاسلكي، ولديھا مصدر للطاقة، وتستوعب مختلف اجھزة الاستشعار والمحركات. النظام | A wireless sensor network (WSN) is a collection of nodes organized into a cooperative network. Each node consists of processing capability, memory, RF transceiver, power source, and accommodates various sensors and actuators. The proposed system in this
1 ... 111 112 113 114 115 ... 202