عرض: 25 50 75 100 النتائج

نتائج البحث: 50 من أصل 10,657

استخدام المادة النانو مسامية SBA - 15 لازالة الملوث العضوي من المياه الصناعية == A Nanoporous SBA - 15 As Adsorbent For Removal of Organic Pollutants From Wastewater

اسم المؤلف: رغد عدنان حبش
اسم المشرف: انعام اكرم صبري | طالب محمد نايف
الموضوع العام: الهندسة الكيمياوية
السنة: 2014
الموضوع الدقيق: العمليات الصناعية
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: تم تحضير ماده السليكا النانويه المسامية (SBA - 15) باستخدام (TEOS) كمصدر للسيليكا و(P123) كقوالب ومن ثم اجريت فحوصات عليها منها حيود الاشعة السينية (XRD),المجهر الالكتروني (SEM)،المساحة السطحيه ( (BET وطيف الاشعة تحت الحمراء (FTIR). بعد ذلك تم دراسة سلو | Santa Barbara Amorphous (SBA - 15) nanoporous silica was prepared using Tetraethylorthosilicate TEOS as silica precursor, Pluronic P123 as template, and characterized by means of X - ray diffraction (XRD), scanning electron microscopy (SEM), BET surface area and fourier transform infrared (FTIR) spectroscopy. The adsorption behavior of methylene blue from synthetic wastewater onto mesoporous SBA - 15 was studied. Both batch and continuous systems were studied. Batch experiments were carried out to measure the adsorption as a function of contact time, initial concentration (15 - 110 mg/l), pH (3 - 11) and adsorbent dose (0.1 - 2.3g/l) to specify the optimum operation condition. The equilibrium of the process was achieved within 20 min. Adsorption isotherms were fitted with the Langmuir, Freundlich and Temkin models. The equilibrium data were best represented by the Langmuir isotherm model with higher correlation coefficient R2 value of (0.990). The kinetics of the MB sorption on SBA - 15 were examined by using pseudo - first and pseudo - second order kinetics models. The kinetics analysis manifested that the overall adsorption process was successfully fitted with the pseudo - second - order kinetic model. In continuous studies, the adsorption of methylene blue from synthetic wastewater onto SBA - 15 in fixed bed was investigated and breakthrough data of the dye was determined. This research is run in small scale column with an internal diameter of 0.7 cm and 35 cm height at constant temperature and pH value. The effect of bed height (3, 6, 9 cm), flow rate (0.6, 1.0,1.4 ml/min) and initial MB concentrations (40, 70, 100 mg/l) on breakthrough curves were investigated. It is found that breakthrough time increases with increasing bed height, but decreases with increasing methylene blue inlet concentration and flow rate. Thomas and Yan models were used to determine the kinetic constants and to predict the breakthrough curves. The experimental data showed a better fit to Thomas adsorption model. In order to find out the possibility of reuse SBA - 15, desorption study was also carried out in this investigation. SBA - 15 can be effectively recovered by calcinations and reused fourteenth times in batch system and five times in continuous system without significant loss in removal of methylene blue from aqueous solution. The long reuse life of SBA - 15 makes it an efficient adsorbent for removal of methylene blue from wastewater at high potential for application in industry.

محاكاة لمعمل الاثلين في العراق باستخدام الاسبن بلسن والماتلاب == Simulation of Iraqi Ethylene Plant Using Aspen Plus And Matlab

اسم المؤلف: هدى عامر عبد القادر
اسم المشرف: صفاء الدين عبد الله النعيمي | زيدون محسن شكور
الموضوع العام: الهندسة الكيمياوية
السنة: 2014
الموضوع الدقيق: العمليات الكيمياوية
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: يعد معمل الاثيلين واحد من اهم معامل البتروكيماويات والاكبر حجما في العالم في الوقت الحاضر. بالاضافة الى ذلك، فانه يعتبر جوهر اي مجمع للبتروكيماويات. وفي مثل هذه المعامل، يخضع الغاز الطبيعي الى العديد من العمليات لفصل مكوناته.الهدف من هذه الدر | Ethylene plant is one of the most important and largest volume petrochemicals in the world today. In addition, it is a core of any petrochemical complex. In such plant, the natural gas is subjected to many processes to separate the components. The objective of this study is to develop a detailed model to simulate an ethylene plant, which includes a pyrolysis section, a separation system and an integrated refrigeration system. An optimization has been performed for a part of the plant; this part is the furnace.The ethylene plant at the Petrochemical Complex in PC1 - Basrah has been considered as a case of study. The kinetics of ethane thermal cracking in pyrolysis furnace has been simulated using Aspen Plus and MATLAB. The radiant coils in furnace have been modeled as a one dimensional plug - flow reactor in which ethane is subjected to steam cracking. The overall plant has been simulated using Aspen Plus version (7.3), and the reactor has been simulated using MATLAB environment, version (2013a) in addition to Aspen Plus. The validity simulation model test has been achieved by comparing the simulation results with the actual data collected from PC1and it showed a great similarity and reliability for both simulation models.A steady state simulation model has been developed to study the behavior of multi - types feed supplied to the plant. Furthermore, the model has been used to evaluate the effects of various process parameters, including temperature of reaction (Reactor outlet temperature), dilution steam to ethane ratio (DS/HC) and the outlet flow rate of hydrocarbons.The other aim of this study is to obtain the optimum operating conditions using Aspen Plus for the reactor in the furnace which has an effect on the final product to determine the maximum profit. Optimization using Genetic Algorithm (GA) by MATLAB has been used as well as Aspen Plus, and a comparison has been made between both methods. The selection of the optimum operating conditions of reactor was obtained to achieve the following objectives together : • Increasing the production rate of ethylene.• Increasing the outlet flow rate of hydrocarbons.These objectives have managed to be achieved all together by maximizing the total profit obtained from the furnace. Finally, Aspen Plus results show that the objectives have been satisfied by manipulating the decision variables Temperature of reaction (Reactor outlet temperature) in the range of (850 - 920) ?C, dilution steam to ethane ratio DS/HC in the range of (0.2 - 0.5) and the outlet flow rate of hydrocarbons ) in the range of (2421 - 1064) Kmole/hr to increase the profit of the furnace to approximately (10.541%) and (5.55%) for the whole plant.

معالجة واستصلاح الماء المصاحب للنفط العراقي باستخدام طريقة عمود التطويف وتقنية الاغشية == Treatment And Reclaiming of Iraqi Oil Field Produced Water By Flotation Column And Membrane Technology

اسم المؤلف: هدى كاظم حسن
اسم المشرف: ثامر جاسم محمد | قصي فاضل عبد الحميد
الموضوع العام: الهندسة الكيمياوية
السنة: 2014
الموضوع الدقيق: العمليات الكيمياوية
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: يتم انتاج كميات كبيره من الماء المصاحب النفطي من قبل شركة نفط الجنوب.يعتبر محتوى النفطي oil - water والاملاح الذائبه TDS من اخطر الملوثات والتي تتم معالجتها باحدث التكنلوجيا في السنوات الاخيره تم استخدام تقنية الاغشية لمعالجة الماء المصاحب النفطي.الهدف م | A large amount of oil field produced water is generated by South Oil Company. Oil - in - Water and TDS are the most serious pollutants for which current treatment technologies are often costly and ineffective in order to reuse water. In recent years, membrane process has been applied for produced water treatment.The aim of the present work is to treat produced water from oil well before being disposed in environment or reused as re - injection to oil well or agriculture water. Oil field produced water is very difficult wastewater to treat and its characteristics change as well to well. The sample test of this study was taken from dehydrator in the DSI/North Rumila/Southern Oil Company in Basrah /Iraq. The treatment process of produced water consists of two stages. The first stage as pre - treatment is achieved by continuous dissolved air flotation (DAF) to reduce the oil content. The second stages, as advanced treatment processes, are accomplished by microfiltration (MF) to reduce the turbidity and nanofiltration (NF) to reduce the salt content as TDS of produced water. The experimental work was carried out using dissolved flotation column is of Perspex glass (0.1 m I.D, 1.5 m height). The bottom of the column connected to a conical joint of QVF glass with a Teflon distributer. The effect of operating parameters (flow rate of produced water, pH, initial oil concentration, flotation time, alum dosage and surfactant of SLS) saturated pressure=5 Atm on the oil content or oil removal efficiency was investigated. The results showed that the oil removal efficiency increases with increasing the flow rate of produced water, the flotation time and coagulants dosage. The oil removal efficiency in DAF unit without coagulants is equal to (80, 94, 95%) for initial oil concentration (30, 50, 70 ppm), respectively at a flow rate 0.03 m3/h and pH=6. While flotation with coagulation, the results indicated that the removal efficiency is equal to 94% (residual oil content <10 ppm) at pH=5, alum dosage=560 ppm, and initial oil concentration=50 ppm, and the removal efficiency is equal to 89.6 at pH=6, alum+SLS dosage=80 ppm, and initial oil concentration=50 ppm. The kinetics of flotation column was studied and it was found that the order of the reaction is changing between zero to first order.The treatment of produced water by membrane technique was carried out by cross flow mode in hallow fiber microfiltration (MF) and nanofiltration (NF). The effect of operating parameter such as transmembrane pressure (TMP) (1, 1.5, 2 bars) with cross flow 20 mL/min, at room temperature, on the flux, rejection, and turbidity and TDS removal was studied. The experimental results by MF manifested that the permeation flux is (108, 156, 611 l/m2.h) and transemembrane pressure is 2 bar at initial turbidity (100, 200, 300 NTU), respectively. But NF, as a final treatment of produced water to reuse, was studied at different feed concentrations (82950, 75050, 67150 ppm) with different TMPS. According to the experimental results, the higher permeation of flux =15 (l/m2.h) at 82950 ppm and 2 bar, was obtained.The experimental results of the removal efficiency were represented in two and three dimensional graphs. An empirical correlation for R% as a function of different parameters (flow rate, pH, and oil concentration) was developed by aided computer using the following formula %R= a + c1*x1n1 + c2*x2n2 + c3*x3n3.

انتقال الحرارة في الغليان الحوضي باستخدام موائع النانو == Pool Boiling Heat Transfer Using Nanofluids

اسم المؤلف: خيرية مطر عيسى الخزاعي
اسم المشرف: جمال مانع علي الربيعي
الموضوع العام: الهندسة الكيمياوية
السنة: 2014
الموضوع الدقيق: الهندسة الكيمياوية
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: يمكن اعتبار نظام المغلي التنوي واحدة من اكثر الطرق فعالية لزيادة التبادل الحراري في منطقة صغيرة نسبيا. انتقال الحرارة في الغليان الحوضي لموائع النانو تم التحقق عنها تجريبيا باستخدام مياه الالومينا AL2O3 ومياه ثاني اوكسيد التيتانيوم TiO2.كموائع نانويه (n | Nucleate boiling regime can be considered one of most effective ways to increase the heat exchange in a relatively small area. Pool boiling heat transfer nanofluid was investigated experimentally using Al2O3 - water and TiO2 - water nanofluids. The experimental test rig consists of boiling vessel and electrically heated plate heating element of stainless steel as heating element. Different concentrations of nanofluids were tested (0.05w %, 0.1w %, 0.3 w%, and 0.5 w %). The nanofluids for Al2O3 and TiO2 were prepared by mixing the( Al2O3 and TiO2) nanoparticles with distilled water in magnetic stirrer for three time periods at (2, 3 and 4) hours and for 1 hour in an ultrasonic bath to suspend the nanoparticles in base fluid. The nanofluids were scanned by scanning electron microscope to ensure well dispersion of nanoparticles in distilled water. Experiments were carried out firstly using pure water then nanofluid to compare the heat transfer enhancement. Results give maximum enhancement ratio in heat transfer rate of (100%) for 0.5% weight concentration for Al2O3 - water nanofluid and (81.82%) for TiO2 - water nanofluid at the same concentration. In both nanofluids the enhancement ratio increases with increased nanoparticle concentrations.This lead to increase in pool boiling heat transfer coefficient.

دراسة حركية التفاعل لوحدة التهديب بالعامل المساعد في مصفى الدورة == Kinetics Study of Catalytic Reforming Process In Daura Refinery

اسم المؤلف: حيدر مجيد خضير
اسم المشرف: محمد فاضل عبد
الموضوع العام: الهندسة الكيمياوية
السنة: 2014
الموضوع الدقيق: الهندسة الكيمياوية
الدرجة: دبلوم عالي
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: Catalytic naphtha reforming is one of the key processes in petroleum refining, converting gasoline boiling range low - octane hydrocarbons to high - octane compounds which can be blended into gasoline. Other valuable by products include hydrogen and cracked light gases. Modeling of a typical semi - regenerative catalytic reformer of Duara refinery has been carried out involving most its key constituent units. Kinetic modeling of the reactions occurring in the fixed bed reactors connected in series formed the most significant part of the overall simulation effort. A reaction scheme involving (15 pseudo components) connected to gether by a network of 30 reactions for components in the C5 - C10 range has been modeled. The Hougen - Watson Langmuir - Hinshelwood type reaction rate expressions are used to represent rate of each reaction. Deactivation of the catalyst was modeled by including the corresponding equations for coking kinetics. It was found that Paraffines and Naphthenes undergo a continuous reduction through the three reactors while the rate of formation of aromatics is becoming slower as the reactants proceed to the third reactor. The reactor of naphtha reforming could be considered as a hydrogen production.

ازالة الكبريت من زيت الوقود باستخدام الاكسدة المعززة بالموجات الفوق الصوتية == Ultrasound - Assisted Oxidative Desulfurization of Fuel Oil

اسم المؤلف: جعفر مازن جعفر
اسم المشرف: نيران خليل ابراهيم | ولاء عبد الهادي نوري
الموضوع العام: الهندسة الكيمياوية
السنة: 2014
الموضوع الدقيق: الهندسة الكيمياوية
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: Due to the dramatic environmental impact of sulfur emissions associated with the exhaust of engines, sulfur content specification for diesel fuels became more and more stringent worldwide. Last environmental regulations for ultralow sulfur diesel require very deep desulfurization processing, which cannot be met by the conventional hydrodesulfurization process (HDS).The present work focuses on benefiting from integrating an ultrasoundassisted oxidative desulfurization process (UAODS) with the conventional HDS process to produce ultra - low sulfur fuels. The proposed method involves a batch ultrasound - assisted oxidative desulfurization process to desulfurize a previously hydrotreated diesel containing 480 ppm sulfur. The oxidizing system used was H2O2/CH3COOH with FeSO4 being used as a catalyst. An ultrasonic probe system was used to enhance the conversion of sulfur - bearing compounds that exist in diesel to sulfones and sulfoxides to affect their removal by a certain separation method, such as extraction or adsorption.The major influential parameters related to UAODS process have been investigated, namely : ratio of oxidant/fuel, ratio of the promoter/oxidant, dose of catalyst, reaction temperature, intensity of ultrasonic waves. A set of comparative studies were also carried out including type of extraction solvent, effect of initial sulfur content, and type of sulfur separation method. Total evaluation for the treated diesel was performed, including GC - MS analysis which has been used to monitor the change of organic sulfur compounds andhydrocarbons in diesel during the desulfurization process.The oxidation treatment, in combination with ultrasonic irradiation, revealed a synergistic effect for diesel desulfurization. The experimental results showed that the removal efficiency for sulfur compounds could amount to 98%, and sulfur level can be reduced to 12 ppm at mild operating conditions (70 and 1 bar). This indicates that this process is so efficient and promising for the production of ultra - low sulfur diesel fuels.The kinetics of the reaction has been also studied. It was observed that the UAODS of diesel fuels fitted pseudo - first - order kinetics under the studied experimental conditions. During this process, values of the apparent rate constant and activation energy were 0.373 min - 1 and 24 kJ/mol, respectively.

تخمين حركية تفاعل ازالة الكبريت للنفثا الثقيلة العراقية == Prediction of Kinetic Reaction of Iragi Heavy Naphtha Desulferization

اسم المؤلف: سها سامي قاسم
اسم المشرف: زيدون محسن شكور
الموضوع العام: الهندسة الكيمياوية
السنة: 2014
الموضوع الدقيق: الهندسة الكيمياوية
الدرجة: دبلوم عالي
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: واحدة من التحديات في مصافي تكرير النفط الخام في الاونة الاخيرة هو الحد من محتوى الكبريت من النفثا الثقيلة الى الحدود الدنيا. في هذا البحث تم اخذ مواصفات محتوى الكبريت للنفثا الثقيلة بمعدل 632 جزء في المليون الى 2.5 جزء في المليون، في درجات حرارة التفاعل ( | One of the recent challenges in the petroleum refineries is the reduction of sulfur content of heavy naphtha to the new lower limits. In this reaserch, was taken the specification of the sulfur content of heavy naphtha at arrange 632 ppm to 2.5 ppm, The range of reaction temperatures is (35 - 175) oC and liquid hourly space velocity (LHSV) at range of (1.3 - 1.4) hr - 1 and hydrogen pressure is 35 bars.The simulators are useful tools to manage operation and to improve the profitability of the process. In this study, excel and Matlab program were developed to simulate hydrodesulferization process (HDS) in vapor phase reactor of heavy naphtha hydrotreating unit of Daura refinery, the comparison between the plan results with HDS reactor model results was made.. Based on the model results the optimum operating conditions were determined. Acomputer program MATLAB (Matrix Laborator) it is software for developed code of kinetic parameter estimation problem using the estimation method and least square as objective function and new GA as solving method. The code was implemented on personal computer (intel (R) Core (TM) i3 CPU, 2.39 GHz processor, 2 GB RAM). The function to be minimized was the sum of squares of the differences between calculated and measured concentration.Genetic optimization method was used to define the parameters of desulfurization reaction kinetic. This hydrotreating reaction kinetic model for desulfurization of Daura heavy naphtha was determined for heavy naphtha boiling point range of (35 - 175) C and using a commercial (HDS) catalyst cobalt - molybdenum (Co - Mo) supported of alumina.The result showed that the order of kinetic reaction was first order for heavy naphtha hydrotreating with (Co - Mo) supported of alumina, and the graphically method is more suitable and less error than optimization method for represent the kinetic reaction for heavy naphtha hydrotreating in Daura refinery.

تطبيقات الطرق العددية في التاكل الكلفاني للمعادن المزدوجة == Applications of Numerical Methods In Galvanic Corrosion of Coupled Metals

اسم المؤلف: بسمة محمد كاظم الشاهر
اسم المشرف: جمال مانع علي الربيعي
الموضوع العام: الهندسة الكيمياوية
السنة: 2014
الموضوع الدقيق: العمليات الصناعية
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: تم دراسة سلوك تاكل معادن النحاس والكربون الصلب والزنك في تراكيز مختلفة من حامض الهيدروكلوريكHCl) ) (0.025، 0.05 و0.075 مولاري ) عند درجات حرارة مختلفة (30، 40 و50 درجة مئوية) باستخدام القياسات الكهروكيميائية (Electrochemical Measurements) في حالة المعا | The corrosion behaviors of metals Copper, Carbon Steel and Zinc in a different concentrations of HCl acid (0.025, 0.05 and 0.075M) at different temperatures (30, 40 and 50°C) were investigated using electrochemical measurements in couple and single state.The galvanic behaviors of coupled metals (Cu - Fe),( Cu - Zn) and (Fe - Zn)were studied using Zero Resistance Ammeter (ZRA) technique, it has been used to measure the galvanic current (Ig) and galvanic potential (Eg) with time. The galvanic corrosion cells for all couples have equal areas of anode and cathode (2×2cm).The galvanic current density (ig) is increased with increasing solution concentration and temperature. The galvanic potential (Eg) is shifted to less negative with increasing solution concentration and temperature and it is close to the corrosion potential of the anode in the couple conditions.The potentiostatic polarization behavior of single three metals (Copper, Carbon Steel and Zinc) in different concentrations of dilute HCl acid (0.025, 0.05 and 0.075M) at temperature (40°C) is found under activation control. The corrosion current density is increases with increasing solution concentration and gives the following arrangement of metals : Cu> Fe > Zn A numerical analysis of galvanic corrosion was presented. The analysis was based on three numerical methods as the boundary element method (BEM), the finite element method (FEM) and the finite difference method (FDM).The potential and current density distributions on the galvanic elements are described by the Laplace equation. The Laplace equation was solved numerically, to determine the potential, current density, and corrosion caused by the galvanic cell using designed computer programs in MATLAB R2014a. The experimentally determined polarization curves have been used in order to define the nonlinear boundary conditions. This boundary value problem has been solved using Newton - Raphson iterative numerical procedure. For the three couple systems (Cu - Fe, Fe - Zn and Cu - Zn), the results obtained for galvanic potential and current density, using the numerical methods (BEM, FEM and FDM) with the overall deviations are 6.689, 10.818 and 18.846 respectively for galvanic current density and 0.631, 1.210 and 1.787 respectively for galvanic potential. From these results it can conclude that the galvanic current density and galvanic potential distribution calculated from the BEM model was in good agreement with the experimental measurements. These are because the main advantages of the BEM over the Finite Element Method (FEM) and the finite difference method (FDM) are high accuracy, discretization on the boundary only which results in a very small number of unknowns, easy dealing with non - regular boundaries and openings that only the domain boundary of interest is required to be discrete, also BEM needs fewer equations and a smaller matrix size than FEM and can solve both finite and infinite domain problems.

تاثير الحماية من التاكل بواسطة الليزر على سبائك الالمنيوم == The Effect of Laser Surface Melting Corrosion Protection On Al Alloys

اسم المؤلف: هبة خميس اسماعيل
اسم المشرف: شذى احمد سامح
الموضوع العام: الهندسة الكيمياوية
السنة: 2014
الموضوع الدقيق: الهندسة الكيمياوية
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: يهدف هذا البحث الى دراسة تاثير المعاملة بالليزر على تاكل سبائك الالومنيوم (7075, 6061, 5083) المغمورة في محلول ملحي (كلوريد الصوديوم) بمختلف التراكيز. وقد تم اعداد عينات من سبائك الالومنيوم ذات ابعاد (2 ملم) سمك وقطر (25 ملم)، وكانت تجارب الاستقطاب في مح | The objectives of the present project are to generate uniform melted layers, free of large second phases to assess the corrosion resistance of the laser treated surface in comparison with the untreated alloy. So disc samples of (7075, 6061 and 5083) aluminum alloys of 2 mm thickness and 25 mm diameter, have been prepared. Polarization tests were carried out in (M lab potentiostat / galvanostat) (Germany) at 298K temperature and (1.5, 2.5 and 3.5) % wt of NaCl solution. The experiments were carried out before and after laser surface melting by (Nd : YAG, MED - 810) pulse laser, system (Q - Switched Nd : YAG 1064/532nm). Before laser surface melting the results showed that the value of the corrosion current density obviously increases with increasing the concentration of NaCl from 1.5% to 3.5%. As well as higher Cl - ions concentration more negative pitting potential (Epit) of aluminum alloys and decrease in the electrochemical stability of aluminum. The corrosion rate for the specimen 7075 is larger than that of 6061 and 5083 aluminum alloys under the same conditions. So it means that the specimens 6061 and 5083 have high resistance to corrosion in NaCl solution After laser surface melting the results showed that the surface of aluminum alloys became more homogenous and pure after treatment.It was found that the corrosion current density decreases after Laser Surface melting at about three orders than that of untreated samples, therefore, the value of the corrosion rate of laser - treated alloy is smaller than that of the untreated. As well as the pitting corrosion potential after Laser Surface melting obviously shifted to more positive direction for all aluminum alloys in different concentrations of the NaCl solution.

تطبيق اللابفيو والخوارزمية الوراثية في السيطرة على مبادل حراري من نوع الصفائح == Application of LabVIEW And Genetic Algorithm For Controlling of Plate Heat Exchanger

اسم المؤلف: ايمن فوزي زوين
اسم المشرف: زيدون محسن شكور
الموضوع العام: الهندسة الكيمياوية
السنة: 2014
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: تم دراسة السلوك الديناميكي لمبادل حراري من نوع الصفائح ( يتكون من 24 صفيحة ) والسيطرة عليه. الموديل النظري للمبادل طور بالاستناد على الموازنة الحرارية لصفائح المبادل.نتائج الموديل توضح السلوك الديناميكي للمبادل حيث تبين انه من الدرجة الاولى بالتقديم ((le | In this work the dynamic behavior of a plate heat exchanger (PHE) (consists of 24 plates) both experimentally and theoretically and the control of the system were studied. A theoretical model for the plate heat exchanger was developed based on the heat balance. A step change is carried in the hot water flow which is considered as a manipulated variable.The results of plate heat exchanger (PHE) showed that the dynamic behavior of plate heat exchanger in this work is dynamically as a first order lead and second order overdamped lag with a significant delay time as shown below : G(p)=(T ?_co (s))/(m ?_h (s) )= ((0.2645s+1.411) e^( - 5.63s))/(0.2156s^2+12.34s+1) The experimental heat transfer measurements of the plate heat exchanger (PHE) indicated that the overall heat transfer coefficient (U) is related to the water flow rate (m) by a correlation having the form : U = 10637 m0.7307 To verify the presented model, temperature control was applied theoretically and experimentally to the plate heat exchanger using conventional P, PI and PID controllers with tuning of control parameters by different methods; Ziegler - Nichols, Cohen - Coon and genetic algorithm to find the best values of proportional gain (Kc), integral time (?I) and derivative time (?D). The time domain specifications like rise time, settling time, overshoot and the performance indices, Integral Squared Error (ISE) and Integrated Time - Weighted Absolute Error (ITAE) were used to evaluate the performance of different control strategies. The PID controller gave better control results of temperature than other controllers, while Ziegler - Nichols tuning method gave better control results than Cohen - Coon. GA technique is the best method in simulation by compare with Cohen - Coon and Ziegler - Nichols methods. Therefore, GA method is suitable as best technique for systems which have shorter constant time.Cohen - Coon and Ziegler - Nichols methods were used in the experimental work to calculate the controller parameters, while GA method was not used in this stage.

تصميم تناسلي تكاملي تفاضلي مضبب للسيطرة على منظومة روبرت ذات ذراع مفرد متصل بمفصل مرن باستخدام تقنية البوابات المبرمجة == Design of A Fuzzy - PID Controller For Single Link Flexible Joint Robot Using FPGA

اسم المؤلف: حسين عظيم عباس
اسم المشرف: اخلاص حميد كرم | اقبال حسين علي
الموضوع العام: هندسة الحاسبات
السنة: 2014
الموضوع الدقيق: هندسة الحاسبات
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: اثناء هذا العمل ستتم مناقشة مشكلة وجود المرونة في مفصل منظومة روبوت ذات ذراع مفرد متصل بمفصل مرن، حيث ان وجوده يسبب نمط من التذبذبات الغير مرغوب بها في استجابة النظام، والتي قد تؤدي الى تدهور اداء النظام وعدم استقرار الاستجابة. ايضا تم اقتراح استخدام مسي | In this work, we have discussed the joint flexibility that exists in a single link flexible joint robotic system which causes poorly damped oscillations thatmay degrade system performance. A fuzzy - PID (Proportional, Integral, Derivative) controller hav

مصادقة الرسائل وتشفير رسالة سمز لتطبيق الروبوت == Message Authentication And Encryption of Sms Message For Android Application

اسم المؤلف: فاطمة اسعد حسن الحبوبي
اسم المشرف: Shaimaa Hameed | Hassan A. Jeiad
الموضوع العام: هندسة الحاسبات
السنة: 2014
الموضوع الدقيق: هندسة الحاسبات
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: The Short Message Service (SMS) is a text based service provided by Global System for Mobile communications (GSM). SMS is one of the most widely, simple and cost effective means for communication between two persons or a group of them.In this thesis a se

تصميم وبناء نظام مراقبة الكتروني للعناية الصحية == Design And Lmplementation of Monitoring System For EHealTh Care Applications

اسم المؤلف: عبد الله علي جواد
اسم المشرف: محمد نجم عبد الله
الموضوع العام: هندسة الحاسبات
السنة: 2014
الموضوع الدقيق: هندسة الحاسبات
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: اصبح نظام مراقبة الصحة الالكترونية جزء ا مھم ا من الحياة اليومية في السنوات الاخيرة. ان التطور الحاصل في الھواتف المحمولة وغيرھا من الاجھزة المحمولة اعطى نظام مراقبة الصحة الالكتروني امكانية استخدام انواع مختلفة من الشبكات. ان نظام مراقبة الصحة الالكترو | E - Health Monitoring Systems (EHMS) have become very important part of our life in recent years. The development of mobile phones and other handheld devices have given the ability to EHMS for using different types of networks. The EHMS consists of many s

تقنيات الاستنباط للبيانات المكانية باستخدام المحلل الجيواحصائي في نظم المعلومات الجغرافية == Interpolation Techniques of Spatial Data Using Geostatistical Analyst In GIS

اسم المؤلف: غصون عيدان عرب ناصر
اسم المشرف: صالح مهدي القرعاوي | حسين زيدان علي
الموضوع العام: هندسة الحاسبات
السنة: 2014
الموضوع الدقيق: هندسة الحاسبات
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: لقد اصبحت التغييرات المناخية في البيئة العالمية مصدر قلق في جميع انحاء العالم في السنوات الاخيرة.وبما ان هطول الامطار يعتبر عاملا مناخيا مهما، فان دراسة انماطه الزمانية والمكانية مهم بالنسبة للباحثين الذين يعملون في العديد من المجالات المتفاعلة في اطار ب | Global environment change has become a worldwide concern in recent years. Rainfall is an important climatological parameter, which is useful for researchers working in many disciplines. In this thesis, spatial interpolation techniques were implemented in

شبكة متحسسات لاسلكية ذكية لادارة انظمة الري بالتنقيط والرش == Intelligent Wireless Sensor Network For Management of Drip And Sprinkler Irrigation Systems

اسم المؤلف: امثال خليل موسى
اسم المشرف: محمد نجم عبد الله | مؤيد صادق كروك
الموضوع العام: هندسة الحاسبات
السنة: 2014
الموضوع الدقيق: هندسة الحاسبات
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: This thesis involves investigation for recent technologies used for monitoring and controlling irrigation systems. Besides, it investigates recent existing WSN technologies and their suitability for agricultural applications so as to adopt the most approp

تحقيق وتنفيذ منظومة التشفير المتقدم القياسي باعتماد مصفوفة البوابات المنطقية المبرمجة حقليا == Implementation of Aes Algorithm Based on FPGA Platform

اسم المؤلف: رلا سامي خضير
اسم المشرف: محمد نجم عبد الله | مهند كاظم صابر
الموضوع العام: هندسة الحاسبات
السنة: 2014
الموضوع الدقيق: هندسة الحاسبات
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: Cryptography plays main role in information security, which is used to protect transformation of electronic data. Advanced Encryption Standard (AES) is symmetric block cipher that includes generation of ciphers for encryption and inverse ciphers for decry

التاثير المتبادل بين المرشح المضبب ومرشح كالمان للتقليل من الضوضاء المختلطة في الصور == Combination of Fuzzy - Kalman Filters To Reduce The Mixed Noise From Images

اسم المؤلف: محمد شاكر محمد النجار
اسم المشرف: اقبال حسين علي | اخلاص حميد كرم
الموضوع العام: هندسة الحاسبات
السنة: 2014
الموضوع الدقيق: هندسة الحاسبات
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: هذا العمل يبحث في تطبيقات تقنيتي مرشح كالمان ومرشح المنطق المضبب لازالة الضوضاء المختلطة ((Gaussian, salt and pepper من الصور الرمادية والملونة. حيث ان ترشيح الصور المشوشة لها اهمية كبيرة في مجالات الحياة العملية مثل الطب, انتاج الفيديو, التصوير, الاستشع | This work deals with the application of Kalman filtering techniques and fuzzy logic filtering due to the fine results it gives for denoising mixed noise (Gaussian, salt and peppers) in gray and color images, where image filtering has great importance in w

مطابقة الخطوط عبر الصور الانعكاسية الانكسارية == Line Matching Across Catadioptric Images

اسم المؤلف: هالة عبد العظيم نعمان الطائي
اسم المشرف: اقبال حسين علي | ظافر رافع زغير الواوي
الموضوع العام: هندسة الحاسبات
السنة: 2014
الموضوع الدقيق: هندسة الحاسبات
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: The 3D techniques today have a wide range of applications, especially in medical and art, it is one of the most promising technologies and important for the future especially in self - drive cars. The error in disparity map and highly computational cost a

تجميع شبكة المحمول المخصص اعتمادا على نظام هجين ظبابي - وراثي == Manet Clustering Based on Hybrid Fuzzy - Genetic System

اسم المؤلف: رؤى عدنان صبري صالح
اسم المشرف: محمد نجم عبد الله | محمود زكي عبد الله
الموضوع العام: هندسة الحاسبات
السنة: 2014
الموضوع الدقيق: هندسة الحاسبات
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: ان الطلب على شبكات التنظيم الذاتي، الشفاء الذاتي دون تدخل من مركزية او بنية تحتية وضعت من قبل / سلطة لمتابعة الزيادة في استخدام الشبكات اللاسلكية. علاوة على ذلك، في شبكة المحمول المخصص ) MANET ( يعتبر اختيار رئيس المجموعة تحديا هاما لا سيما في البنيه الح | The demand for self organizing, self healing networks without the interference of centralized or pre - established infrastructure/authority has been adopted to follow the increase in usage of wireless networks. Furthermore, in Mobile Ad hoc Network (MANET

نظام مراقبة قليل القدرة يعتمد على شبكات المتحسسات اللاسلكية == Low Power Monitoring System Based on Wireless Sensor Network

اسم المؤلف: قصي شهاب حمد
اسم المشرف: صالح مهدي القرعاوي | مؤيد صادق كروك
الموضوع العام: هندسة الحاسبات
السنة: 2014
الموضوع الدقيق: هندسة الحاسبات
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: تعتبر انظمة المراقبة وكشف التطفل شرط مهم لامن الشركات والمؤسسات وحتى بالنسبة للمستخدم العادي. اعتمدت الانواع السابقة من انظمة المراقبة على البشر لادارة عملية المراقبة يدويا. استخدمت تكنولوجيا المتحسسات اللاسلكية في الوقت الحاضر في انظمة المراقبة على مدى و| Monitoring and intruder detection systems have been considered as the most important security condition for companies, institutions and even for the individual users. The old versions of the above systems depend on humans to manage the monitoring manually

تصميم وتنفيذ نظام مراقبة FECG عن بعد بالاعتماد على موقع الكتروني == Design And Implemetation of Remote Web - Based Fetal Electrocardiogram (fecg) Monitoring System

اسم المؤلف: نور عبد الخالق زغير القريشي
اسم المشرف: صالح مهدي القرعاوي | مؤيد صادق كروك
الموضوع العام: هندسة الحاسبات
السنة: 2014
الموضوع الدقيق: هندسة الحاسبات
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: Recently, healthcare monitoring systems have utilized the modern wireless networks and internet technologies. One of the most developed applications in the healthcare monitoring systems is the fetal heartbeat detection. Obtaining fetal heartbeat has becom

مصادقة المستخدم بالاعتماد على الميزات الديناميكية لضربات المفاتيح باستخدام الشبكة العصبية وطريقة تحليل المكونات الرئيسية == User Authentication Based on Keystroke Dynamics Features Using NN And PCA

اسم المؤلف: مينا خضر عبيد
اسم المشرف: شيماء حميد شاكر | رياض جبار سوداني
الموضوع العام: هندسة الحاسبات
السنة: 2014
الموضوع الدقيق: هندسة الحاسبات
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: تعتبر ديناميات ضربة المفتاح خيارا جيدا للمصادقة على المستخدم بدلا من المصادقة المعتمدة على كلمة المرور التقليدية؛ كلمات السر هي عرضة لهجمات كلمة المرور. ديناميات المفاتيح تعتمد على ميزات التوقيت التي تستخرج عندما يقوم المستخدم بالكتابة باستخدام لوحة المفا | As a behavioral biometrics, Keystroke dynamics are considered a good choice for user authentication rather than the traditional password - based authentication; passwords are vulnerable to password attacks. Keystroke dynamics depend on the timing features

طريقة محدثة لعملية تمييز الصوت == A Modified Approach For The Sound Recognition Process

اسم المؤلف: مروة فاضل جاسم
اسم المشرف: ازاد رحيم كريم
الموضوع العام: هندسة الحاسبات
السنة: 2014
الموضوع الدقيق: هندسة الحاسبات
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: The issue of discrimination of the sounds is one of the very important issues and has many applications in the field of identifying the sources of the sounds. So there are a lot of researches nowadays that serve this subject and are all looking for the be

تمييز الغير مباشر للحروف اليدوية بواسطة الشبكات العصبية اعتمادا على عدة خوارزميات لاستخلاص الخصائص == Offline Hand Written Letter Recognition Using Neural Networks Based on Multiple Feature Extraction Algorithms

اسم المؤلف: مريم خلف كاظم
اسم المشرف: باسم عبد الباقي جمعة | اياد غازي ناصر
الموضوع العام: هندسة الحاسبات
السنة: 2014
الموضوع الدقيق: هندسة الحاسبات
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: ھو احد حقول البحث في تمييز الانماط والذكاء الاصطناعي. نظام (LR) تمييز الحروف يمكنك من تحويل كتاب او مقالة في مجلة الى ملف في الحاسوب كنسخة الالكترونية، ومن ثم LR تحرير الملف باستخدام محرر نص مثل معالج النصوص. الاسلوب الاكثر شيوع التعليم الشبكة وھذه الخوا | Letter recognition (LR) is a field of research in pattern recognition, artificial intelligence and machine vision. A LR system is used to transform a scanned book or magazine article into an editable text form. In this work, letter recognition using Arti

تصميم وتنفيذ خوارزمية توجيه ذكية لشبكات الحزم ذات النطاق الواسع == Design And Implementation An Intelligent Routing Algorithm For Large Scale Packet Networks

اسم المؤلف: احمد ناهض حمزة
اسم المشرف: منى محمد جواد | محمود زكي عبد الله
الموضوع العام: هندسة الحاسبات
السنة: 2014
الموضوع الدقيق: هندسة الحاسبات
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: Routing algorithms are the key elements in determining the network performance. Therefore, in this thesis a model of logical topologies in the software has been proposed to examine the performance of the logical topologies and their routing algorithms for

تخمين وازالة الضوضاء من الصور الملونة بالاعتماد على المنطق المضبب والتمثيل البياني == Color Image Noise Estimation And Removing Based on Fuzzy Logic And Histogram

اسم المؤلف: عادل جلال يوسف
اسم المشرف: منى محمد جواد | اقبال حسين علي
الموضوع العام: هندسة الحاسبات
السنة: 2014
الموضوع الدقيق: هندسة الحاسبات
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: تكون الصورة المراقبة في العديد من تطبيقات معالجة الصور الرقمية, ملوثة بسبب الضوضاء الذي يحدث اثناء اكتساب او ارسال الصور. حيث ان الضوضاء يقلل من جودة الصور ويؤدي الى نتائج غير مرغوب بها في المراحل المتعاقبة من معالجة الصور (مثل التقطيع, تميز الشكل, التحسي | In many of digital image processing applications, observed image is often corrupted by noise which may arise during image acquisition or image transmission. Noise reduces image quality and leads to unwanted results of subsequent stages of the image proces

تحسين التمييز للشبكات العصبية المنعدمة الاوزان == Recognition Enhancement of Weightless Neural Network

اسم المؤلف: عمار علي مصطفى
اسم المشرف: محمود حمزة المفرجي
السنة: 2014
الموضوع الدقيق: هندسة الكهرباء
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الكلمات الدلالية:
  • Pattern Recognition
  • RAM - based Weightless Neural Network
الصفحات الاولى:
المستخلص: الفعل الذكي للشبكات المتعلمة في هذا البحث يركز على الشبكات المتعلمة في منظومة تمييز الانماط المعتمدة على الذاكرة. ان الفعل الذكي في هذه المنظومات يكمن في القابلية على تمييز الانماط التي لم تتدرب عليها مسبقا وذلك يتم بالاعتماد على ظاهرة التعميم. الهدف من ا | The intelligent action of the learning network in this research concentrates on the learning network in the pattern recognition systems that are based on the Random Access Memory. The intelligence action in the pattern recognition system is the capability to recognize other patterns that were not learned before in the system depending on the generalization. The objective of the research is oriented to improve the performance of the learning network in pattern recognition system. A pattern recognition system that based on Random Access Memories is developed and evaluated for classifying non - deterministic data with particular reference to unconstrained handwritten Arabic numerals and traffic signs patterns.Various techniques are presented which allow the system to be optimized, giving an increase in the performance and confidence of the results.The results obtained showed the improvements of n - tuple and VG - RAM WNN systems as learning network. Techniques used to enhance the performance are investigated. The averaging of the training patterns for colored images is the proposed system. This technique gives improvements to the system performance in term of required storage size and recognition speed.

تحسين الفولتية وتقليل خسائر منظومة الشبكة العراقية باستخدام افضل جهاز FACTs == Improvement of Voltage Profile And Reduce Iraqi Grid System Losses By Using Optimal FACTs Device

اسم المؤلف: سيف اسعد عبد الحسين
اسم المشرف: رشيد حميد الربيعي | انعام ابراهيم علي
السنة: 2014
الموضوع الدقيق: هندسة الكهرباء
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: الغرض من هذا العمل هو تحسين الجهد والتقليل من خسائرالقدرة للشبكة العراقية ( 400kV ) عن طريق تركيب اجهزة ( FACTs ) في مواقع مختلفة تحت حالة خطا ومقارنة النتائج مع تلك دون وجود (FACTs) تحت نفس الظروف.تم تحديد الموقع الامثل للـ(FACTs) على اساس الخوارزميات | The aim of this work is to improve the voltage profile and reduces power losses of Iraqi (400kV) power grid system by installing Flexible Alternating Current Transmission System devices (FACTs).The optimal location of the FACTs device was specified based on Genetic Algorithm (GA) optimization method and power system analysis toolbox ( PSAT) package, it was utilized to search for optimum FACT parameters setting and location based objective function that depends on the power and voltage as fitness.MATLAB (R2011a) was used for running both GA program and Power System Analysis Toolbox (PSAT) version 2.1.6, Newton Raphson method also used for solving the load flow of the system and the Trapezoidal method for the non - linear differential equations.Two systems have been implemented in this work as follows; • IEEE - machine 9 - bus system.• INSGS 11 - machine 24 - bus, 39(400kV) overhead transmission line.The GA program is implemented on IEEE 9 - bus system, then after getting the appropriate results the same procedure repeated for the Iraqi grid system which is more complicated, its used to find the optimal location of Unified Power Flow Controller (UPFC). The results obtained from GA have been compared with PSAT and showed that the installation of (UPFC) devices at the optimal locations of the Iraqi grid gives an improvement in the power losses and voltage after subjected to the three phase fault to ground at different locations and different cases (temporary fault, permanent fault).

تصميم مسيطر وتحليل مولد حثي ثنائي التغذية مع سرعة الرياح المتغيرة == Controller Design And Analysis of Doubly - Fed Induction Generator With Variable Speed Wind

اسم المؤلف: سراج منهل حمید
اسم المشرف: حسین ثاني رشك
السنة: 2014
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: The Wind Energy is one of renewable energy and has become very popular and more attractive, as a result of many factors, some of these factors are, rising oil prices, worldwide awareness of the decline in world oil production, an raise in the price of natural gas. Therefore the need for renewable energy has been very important.This work deals with Doubly Fed Induction Generator (DFIG) based wind turbine. By studying the performance of DFIG connected to the grid with constant and variable speed wind. Three cases are considered and implemented using Matlab/Simulink. The first case is studied the effect of the size of capacitance at DC - bus with constant wind speed using space vector pulse width modulation (SVPWM) switching frequency 10KHZ and two values of capacitance.The second case is studied the effect of three phase fault condition, at 33KV line.The third case is that when the input is variable speed wind, the simulation results illustrate that is with variable wind speed and conventional values of PI controllers gains the generator system behavior show increasing in rising time and maximum overshoot of generated power, the control circuit is needed for optimization to improve the generated power. This optimization can be made by tuning the controllers parameters with optimal values, so the optimization is made by using Particle Swarm Optimization (PSO). The new optimal controllers parameters(PI - PSO) make the system more efficient from the results by reducing the ripple of DC - Voltage and maximum overshoot. And the generated active power get more smooth and rising time has been reduced.

تصميم ترميز تحويل لوبي في القنوات الاسلكية == Design of Luby Transform Code Over Wireless Channel

اسم المؤلف: نبيل احمد مصدق
اسم المشرف: وائل عبد الحسن هادي
السنة: 2014
الموضوع الدقيق: هندسة الاتصالات
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: ترميز التحويل لوبي) هو نوع من الترميز النافوري يعمل بدون اي معلومات عن القناة. في هذا العمل، تم تصميم LT code)) باستخدام ماتلاب، التصميم يتكون من ثلاثة اجزاء ( Encoder ,Decoder, channel ). في الجزء الخاص بتصميم الـ (Channel ) استخدمنا (( flat fading ch | Luby transform code (LT Code) is a type of fountain codes operating without any information about channel. In this work, LT code design of LT code implemented by using Mat lab as simulation software, our design consists of three parts (encoder, channel and decoder). In the channel design, flat fading channel will be used as a noisy channel to measure the performance of LT code over this type of channels. From the result obtained, SNR improvement by (30dB) at (BER=?10?^( - 4)) compared with data effect by the fading channel without coding with BPSK modulation model under different values of degree of distribution (d). Other type of modulation model (QPSK) used to measure the effect of changing the modulation type on the code performance. From the results obtained, SNR improvement by (31dB) at (BER=?10?^( - 4)) compared with data effect by the fading channel without coding. The degree of distribution (d) is a critical point of design, two types of distribution presented in this work, robust soliton distribution (RSD) and ideal soliton distribution (ISD). (ISD) works poorly in practice, (RSD) is a practical way used to get the degree of distribution in design by adding two extra parameters (c and ? ) which provide the spike element (k/R) in high degree distribution to ensure the continued of decoding process. As a result obtained the value of (c) has a major effect on the spike position on high degree (c=0.15,k/R=10 and c=0.2,k/R=7) with selective value of ?=0.5.The successful decoding probability for two types of degree distribution is very important, the value of successful decoding probability for (ISD) for low number of encoding packets (50 - 100) packet is greater than the value of successful decoding probability for (RSD). In the high number of encoding packets (>150) the value of successful decoding probability for (RSD) is greater than the value of successful decoding probability for (ISD).Encoding time for two type of distribution also discussed in this work, based on the results obtained the encoding packets time when using (RSD) is less than the encoding packets time when using (ISD).

تخمين حالة منظومة الشبكة العراقية استنادا الى تقنية امثلية الحشد الجزيئي == Iraqi Super Grid Network State Estimation Using Particle Swarm Optimization (PSO) Techniqu

اسم المؤلف: انمار جاسم حميد
اسم المشرف: افانين انور عبود
السنة: 2014
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: يعتبر تخمين حالة منظومات القدرة الكهربائية من الامور المهمة في تشغيل منظومات القدرة وخصوصا في حالة الحمل الزائد على شبكة الطاقة الكهربائية من خلال دوره في ضمان تشغيل اكثر اقتصاديا وامانا. تم في هذا العمل دراسة تخمين حالة منظومة القدرة واقتراح طريقة فعا | Due to the increasing stress on power system networks, state estimation recently became a main matter in the operation of power systems through its important role in ensuring the secure and economical operation of the power system. This work presents a study of a problem of power system state estimation, and proposes an efficient and reliable optimization approach to solve the power system state estimation problem. Two programs have been proposed and implemented in order to overcome the disadvantage of the classical optimization problem and search for the optimal solution of state estimation in power systems, the first program is a conventional state estimation program based on Weighted Least Square (WLS) method, and the second program is an intelligent program based on Particle Swarm Optimization (PSO) technique. All programs have been implemented using MATLAB and have been developed to solve the state estimation problem of the Iraqi Super Grid network (400kV). The proposed programs have been examined and tested on the 14 - bus IEEE and 30 - bus IEEE test standard system. The results were compared with those of the previous published papers. Then, the two programs were applied on the Iraqi Super Grid network (400 kV). The tests proved that the two methods are very efficient and suitable for on - line applications since they are concise and require few computations. The results show that the convergence of the (PSO) technique to the optimal solution is more accurate than (WLS) method. On the other hand, the PSO has an acceptable execution time compared with the freezing time of Iraqi Supervisory Control and Data Acquisition (SCADA) system approved by the Iraqi national grid.

تصميم وتنفيذ رادار تضمين التردد ذو الموجة المستمرة لنظام السرعة التكيفي للسيارات == Design And Implementation of Frequency Modulation Continuous Wave Radar For Adaptive Cruise Control of Car Applications

اسم المؤلف: تمارا زهير فاضل
اسم المشرف: منال حمادي جاسم
السنة: 2014
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: The traffic accidents became significantly obsession and concern for all members of society, and has become one of the most important problems that sap physical, human resources and human potential. The researches show that the damaged property and other costs may equal 3% of world’s gross domestic product, which have been required to work in finding solutions and suggestions and put them into practice to reduce these incidents.The insertion of preventive safety applications into the car system can avoid the above mistakes. In this work, a design and implementation of Frequency Modulation Continuous Wave (FMCW) radar system working at 77GHz for Adaptive Cruise Control (ACC) technology is proposed. Using MATLAB R 2013 which is a flexible system to estimate the speed and distance in accordance to vehicle ahead, which reduces the forces on the rate of accidents by warning the driver when two vehicle become too close.Also, the principle of FMCW radar is presented to generate Linear Frequency Modulated Continuous Wave (LFMCW) sweep waveform through frequency bands with triangular frequency modulation using Voltage Control Oscillator (VCO), a triangle sweep pattern adopt will resolve ambiguity without Doppler processing. which improves the decision making before hardware implementation.Proteus Professional v8 and Micro C PRO v 6.1 compiler is used for Peripheral Interface Controller (PIC) to design a proposed collision warning circuit with PIC16F887 and RS_232 serial port to send data using USART terminal for (short, middle, large) test range.A serial communication interface is used for sending the simulation results from MATLAB FMCW radar system to hardware easy PIC v7 board with PIC16F887 to forward collision warning circuit to alerts the driver of collision risk, Liquid Crystal Display (LCD) shows radar status (short, middle, large) in accordance to range between the vehicle that FMCW radar installed and the vehicle ahead.Graphic Liquid Crystal Display (GLCD) shows the car position and road lines. Piezo Buzzer will start singing to alerts the driver from danger road.The simulation design is achieving the desired performance, one parameter warrants further attention. In the FMCW configuration, the sweep time is about 25 microseconds. Therefore, the system needs to sweep a 140 MHz band within a very short period. Such an automotive radar may able to meet the cost requirement.

تقييم اداء الكشف المباشر والمتشاكه في نظام اتصال الليفة الضوئية == Performance Evaluation of Direct And Coherent Detections In Optical Fiber Communication System

اسم المؤلف: علاء عبد الزهرة جعفر
اسم المشرف: علي يوسف فتاح
السنة: 2014
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: تطورت خدمات الاتصالات بشكل متسارع في السنوات القليلة الماضية خصوصا في المسافات بعيدة المدى وبمعدل نقل البيانات بدقة عالية وخسائر قليلة في جميع انحاء العالم. وقدمت تقنيات مختلفة لزيادة سعة الارسال في انظمة اتصالات الالياف الضوئية بواسطة جمع مسارات البيانا | In recent years, there has been an extensive development of optical fiber services. They provide transmission over long distances at a high data rate with few losses all over the world. Different techniques have been introduced to increase the transmission capacity of optical fiber communication systems by a multiplexed high data rate stream into an optical fiber such as Dense Wavelength Division Multiplying (DWDM) technique. Since the deployment of DWDM technique, the focus on introducing large system capacity with high system performance, different detection techniques have been introduced to enhance the system performance with high sensitivity. In this work, two types of detection techniques (direct and coherent detection) have been evaluated and compared with each other. These detection techniques have been evaluated based on several models of encoding format such as Return to Zero - Differential Phase Shift Keying (RZ - DPSK) and Non Return to Zero - Differential Phase Shift Keying (NRZ - DPSK) at 10 Gb/s as a data rate.These systems were first simulated with a single channel to analyze the performance with no Stimulated Raman Scattering (SRS), Cross Phase Modulation (XPM) and Four Wave Mixing (FWM) effects. Whereby the system of 8×10 Gb/s is simulated at 200 GHz, 100 GHz and 50 GHz as channel spacing. Three types of dispersion compensation schemes are used in the link channel. These systems are simulated using (Optisystem version 10.0) software package. The performance of the designed systems are evaluated through Q.factor verses input power and Bit Error Rate (BER) verses Signal to Noise Ratio (SNR).The polarization interleaving is used with the WDM systems to decrease the nonlinear effects and the crosstalk arising among the adjacent channels.The obtained results of the 67% RZ - DPSK arrived to the threshold power at input power less than of the 50% RZ - DPSK, as well as the 50% RZ - DPSK system arrived to maximum Q.factor lower than 33% RZ - DPSK. This is due to the pulse duration of 33% RZ - DPSK is smaller than of 50% and 67% RZ - DPSK.The results show that the coherent detection technique has better performance than the direct detection technique. The coherent detection technique has Q.factor equal to 45, while the direct detection has Q.factor equal to 27 at the same input power ( - 5dBm), while the coherent detection technique arrived to the threshold power at the input power less than of the direct detection technique.The BER of the 33% RZ - DPSK with coherent detection with 10 Gb/s at 300 km as transmission distance achieved ?10?^( - 12.9) at SNR of 10 dB, while for the 33% RZ - DPSK with direct detection is achieved a BER of ?10?^( - 8.8) with SNR of 10 dB.The performance of the proposed systems has been improved extrusivly with increase the space channel, where the performance of the systems at 200 MHz as channel spacing has best performance than 50 MHz as channel spacing.By adapting coherent detection with 33% RZ - DPSK technique of 200 MHz as channel spacing, DWDM system can carry high data rate with long - haul transmission distance.

الشبكات المتعلمة الرقمية متعددة الاصناف المحورة لاغراض فحص كريات الدم الحمراء == Modified Multi - Category Digital Learning Network For Red Blood Cell Inspection

اسم المؤلف: سهاد قاسم غلام حسين حداد
اسم المشرف: محمود حمزة المفرجي
السنة: 2014
الموضوع الدقيق: هندسة الالكترونيك
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الكلمات الدلالية:
  • Pattern Recognition
  • RAM - based Weightless Neural Network
الصفحات الاولى:
المستخلص: A pattern recognition system based on the n - tuple technique is developed and evaluated for use in classifying non - deterministic data with particular reference to medical image. The pattern recognition system presented in this work fulfills the requirements of simplicity and efficiency making it attractive to practical use in present day for industrial and medical environments. It is an effective solution for providing healthcare with reduced cost, especially for the rural areas and far away patients. Ordinary doctors (not specialist in blood diseases), will be able to perform extra - ordinary tasks.In this work Digital Learning Network has been designed for classification of different shapes of abnormal Red Blood Cells. Digital Learning Network is of low cost hardware and implementation, and one shot learning, using networks of RAMs. Many parameters have been investigated in details which affect the recognition rate. These parameters are presented to allow the system to be optimized, giving an increase in the performance of the system. Modification method of Feedback Digital Learning Network, which is an improving process of Digital Learning Network, has been implemented. The obtained results show that high performance (96.6%) can be achieved, providing evidence of the validity of the proposed technique.

اعادة تشكيل واضافة متسعات في قطاع توزيع كهرباء بغداد == Reconfiguration And Capacitor Placement In A Baghdad Distribution Sector

اسم المؤلف: اديب ناصر حسين
اسم المشرف: ثامر محمد عبد الوهاب
السنة: 2014
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: يعد تخطيط شبكات التوزيع الكهربائية من الاولويات في الوقت الحاضر في العراق نظرا للزيادة الهائلة في الاحمال الكهربائية والتوسعات المفروضة على الشبكات نتيجة التوسع العمراني الكبير والسريع.يتحقق الاداء الامثل للشبكة بتقليل المفاقيد‘ تحسين الجهد (Voltage pr | Planning of electrical distribution networks is considered of highest priority at the present time in Iraq, due to the huge increase in electrical power demand and expansions imposed on distribution networks as a result of the great and rapid urban development. Optimum performance of the electrical network is achieved by reducing losses, improving voltage profile and alleviating overload for the system components. Such operation provides for energy salvage and redundancy in the electrical network. A planning method is proposed in this work to achieve optimum operating conditions of the network by combining the network reconfiguration in conjunction with the insertion of capacitors of optimal sizing and locations. This method is classified as a huge discrete non - linear optimization problem due to the large number of variables along with the presence of constraints and objectives. The power losses and voltages in buses for all cases are obtained by backward/forward load flow method. The proposed planning of distribution networks is based on the powerful and advanced CYMDist software as a tool for the simulation of distribution networks and performing the required analysis. CYMDist is practical and efficient analysis software, which is used by many electrical companies worldwide as well as the Iraqi ministry of electricity.Optimal network reconfiguration and capacitor placement methods are tested on IEEE 33 - bus and IEEE 34 - bus test systems, respectively. The results show excellent matching as compared with previous work mentioned in the literature.The work is implemented on an actual sector from Baghdad city distribution network, which is Al_Bayaa 11kV, 145 bus, four feeders system. The presented results show that minimum active power losses with improved voltage profile had been achieved. So the network can operate normally without any constraints violation.

تحليل الاضطراب لتوربينة الرياح المربوطة مع منظومة القدرة == Disturbance Analysis of A Wind Turbine Connected With Power System

اسم المؤلف: احمد نجم عبد الامير
اسم المشرف: كنعان علي جلال
السنة: 2014
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: نظرا لزيادة الطلب على الطاقة في السنوات الاخيرة نتيجة للتوسع السكاني والصناعي ولتقليل التلوث الناتج من الوقود التقليدي والحفاظ على البيئة مما دعت الحاجة الى استخدام مصادر بديلة للطاقة, والتي يجب ان تمتاز بعدة ميزات اهمها انها صديقة للبيئة وغير قابلة للنفا | According to increasing the demand for energy in recent years as a result of the expansion of the population and to reduce pollution from conventional fuels, the need arises to find alternative sources of energy which must be characterized by several features, most important of which is friendly to the environment and sustainable. In this work, the effect of different types of disturbances on the performance of fixed speed of wind turbine generator type Squirrel Cage Induction Generator (SCIG) connected to the power system has been investigated, because it has features which make the best choice in some cases, despite the less efficiency compared with other types of generators. Also, this work aims to study and analysis the effect of (STATCOM) on the wind turbine generators because of its advantages in improving voltage stability of the grid and improving the quality of the productive power. The proposed work is performed using MATLAB/Simulink. The intelligent systems have been used to obtain the best performance in terms of extracting more power from wind energy as well as increase the stability of system in situations of disturbances and the results obtained have been compared with conventional control systems.Three types of controllers are proposed in this work; the first controller is the Proportional - Integral (PI) based on classical trial and error method, the second controller is PI - controller based on Particle Swarm Optimization (PSO) technique for optimal tuning (gain) to improve the performance of the system. The results obtained proved that the PI - controller based on Particle Swarm Optimization (PSO) technique is better than based on trial and error method. The third controller is (Nonlinear Auto regressive - Moving Average) NARMA - L2 based on (PSO). Finally, the results of the proposed controllers show that NARMA - L2 controller is more effective on the stabilization and improves the performance of the system compared with PI - PSO controller

تقييم اداء المسافية بوجود اجهزة FACTS == Distance Protection Performance Evaluation In Presence of Facts Devices

اسم المؤلف: امير عقيل محمد
اسم المشرف: قيس متي الياس
السنة: 2014
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: With limited enhancement or expansion of the transmission infrastructure, the contemporary power systems are operating under more stressed conditions. It becomes important to fully utilize the existing transmission system to supply load demand as much as possible, thus eliminating or reducing the need for new transmission investment. Flexible AC Transmission System (FACTS) technology provides a method to fully utilize the existing transmission lines as well as new and upgraded lines. However, the implementation of FACTS devices in the transmission system has introduced new power system dynamics that must be addressed in the area of power system protection, such as rapid changes in line impedance, line current and voltage. This thesis reports the results of comprehensive study carried out to explore the impact of mainly two of the FACTS devices, Static Synchronous Compensator 'STATCOM' and Unified Power Flow Controller 'UPFC', on the distance protection relaying system in order to identify important issues that protection engineers need to consider, that is during the stages of design and operation of the protection system. Simulation studies are carried out using MATLAB/SIMULINK. First, the distance relay has been modeled and validated with FACTS device models using test systems from literature. Then the distance relay performance is analyzed and evaluated for various fault and loading conditions in the presence of FACTS devices. A comprehensive study and results for one of the Iraqi 400kV transmission lines (KDS4 - NSRP transmission line) are presented and useful recommendations can be presented to the General Directorate of electrical Power Transmission for Middle Euphrates region / Iraqi Ministry of Electricity. II Abstract Generally, the results show that the apparent impedance seen by the distance relay would be different from that of the system without FACTS devices. Due to this, the distance relay may malfunction, resulting in undependable operation of the power system protection during faults. Furthermore, the results show clearly the dependency of the distance relay operation on many design and operational factors. These include the FACTS device type and its use purpose, the FACTS device connection point or location, the fault type and fault point location along the line, the power flow,...etc.

تحسين استقرارية منظومة الشبكة العراقية (kV 400) باستعمال افضل جهاز من اجهزة ال FACTS == Stability Improvement of The (400kV) Iraqi Grid Using The Best FACTS Device

اسم المؤلف: شيماء شكري عبد الحليم
اسم المشرف: رشيد حميد الربيعي
السنة: 2014
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: يعتبر نظام القدره الكهربائيه من الانظمه الضخمه والمعقده لاحتوائها على عدد كبير من محطات التوليد وخطوط النقل واجهزة السيطرة لذلك فانه يخضع الى تغيرات مفاجئه في مستويات الحمل، حيث اصبح من الصعب جدا الحفاظ على نظام مستقرمع التغيرات التي يشهدها النظام, لذلك | Electrical power system has become large and complicated so it is susceptible to sudden changes in load levels. Stability is an important concept which determines the stable operation of power system.The modern trend is to employ Flexible Alternating Current Transmission System (FACTS) devices in the system for effective utilization of transmission resources. The FACTS devices contribute to power flow improvement besides they extend their services in transient stability improvement as well, study and analyze the stability of system through rotor angle and voltage. The objective of this work is to improve the transient stability of the Iraqi National Super Grid System (INSGS) by using best FACTS device in different optimal locations under fault conditions. Two test systems are studied, the first system is IEEE 9 - bus test system, and the second system is the Iraqi (400 kV) electrical network 24 - bus bars, three phase to ground fault, temporary fault and permanent fault are tested. The load flow program was implemented using Newton - Raphson method and the numerical solutions of non - linear differential equations are solved using Trapezoidal method. The programs that are used in this work are implemented using MATLAB 7.12.0(R2011a) package based on Power System Analysis Toolbox (PSAT version 2.1.6)software.copyright © 2002 - 2010 by Federico Milano as Graphical User Interface. A comparison has been made between five types of FACTS (UPFC, SSSC, TCSC, SVC, STATCOM) at optimal locations of the Iraqi grid and 9 - bus test system to get optimal FACTS devices by (voltage stability and rotor angle stability). The results obtained show that Unified Power Flow Controller (UPFC) is an optimal device for improvement the stability by damping the voltage and rotor angle oscillations.

التركيب السليكوني النانوي في الخلايا الشمسية == Nanostructured Silicon Based On Solar Cells

اسم المؤلف: نور احمد سلمان
اسم المشرف: ثائرة زكريا الطيار
السنة: 2014
الموضوع الدقيق: هندسة الالكترونيك
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: تعتبر الخلايا الشمسية تكنولوجيا واعدة وقابلة للتجديد حيث ازداد الطلب عليها نتيجة لزيادة الاهتمام بالطاقة الكهروضوئية. ان التحسين المستمر لكفاءة الخلايا الشمسية بايجاد التقنيات والمفاهيم الجديدة يجب ان يمتد على نحو متزايد باعتبارها واحدة من اهم مصادر الط | The demand for solar cells has been growing rapidly with an increasing social interest in photovoltaic energy. The improvement of energy conversion efficiency of solar cells is performed by developing the technology and concepts that have been increasingly extended as one of the key components in our future global energy supplement. But, the main problem of photovoltaic modules are their rather high production and energy cost. Three generations of solar cell technologies have been established in the previous century.Nanostructured silicon substrates based on p - type crystalline Silicon (c - Si) have been prepared in this work. Electrochemical Etching (ECE) of the Silicon (Si) wafers in Hydrofluoric (HF) acid was employed to synthesize porous layers consisting of silicon nanostructures. The process was carried out at different etching time and different current densities which are considered as effective parameters in ECE process. It is found that a homogeneous porous layer could be obtained with porosity value of (87%) when the current density is (60 mA/ cm2) and the etching time of (10 min). Among the Transparent Conductive Oxide (TCO) materials available, Zinc Oxide (ZnO) films show promising electrical and optical properties in combination with low cost alternatives. It can function as Anti - Reflecting Coating (ARC), window material, transparent electrode and active layer in heterojunction solar cells. n - type ZnO thin films are grown on p - type nanostructured silicon substrates by using Pulsed Laser Deposition (PLD) technique with Q - switching Nd : YAG laser beam Second Harmonic Generation (SHG) [?=(532 nm), number of pulses (140) pulses, and laser energy (820 mJ)], vacuum of (10 - 3 Torr), ambient oxygen pressure of (10 - 1 Torr), and substrate temperature of (400 °C). The morphological, optical, chemical and structural properties were investigated using Atomic Force Microscopy (AFM), Ultraviolet - Visible (UV - VIS) spectroscopy, Fourier Transform Infrared (FTIR) spectroscopy, and X?Ray Diffraction (XRD) techniques, respectively.Surface morphology and optical properties results show densely packed highly crystalline growth of ZnO thin film on nanostructured silicon substrate grown at optimum condition with an average grain size around (88.57 nm). The average roughness, root mean square, and ten - point height estimated from AFM quantitative analysis, are found to be (3.02 nm), (3.62 nm), and (8.76nm) respectively. The thickness is calculated and found to be (100 nm). The film shows high transparency (above 80%) and the estimated Energy - gap (Eg) is found to be about (3.4 eV). This is important for its applications as transparent conductive films and solar cell windows. The chemical and structural properties results characterize ZnO at (420 cm - 1) and (766 cm - 1) absorption bands respectively and the thin film is polycrystalline with hexagonal Wurtzite structure.

تصميم وتنفيذ ذراع الي موجه عن طريق اشارة تخطيط العضلات باستخدام المتحكم الدقيق == Design And Implementation of A Robot Arm Driven By EMG Signal Based On Microcontroller Unit

اسم المؤلف: انس عبد الحميد كاظم
اسم المشرف: خالدة شعبان رجب
السنة: 2014
الموضوع الدقيق: هندسة الالكترونيك
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: تعتبر اشارة (EMG) هي الاشارة المكتشفة على سطح الجلد فوق العضلة والمتولدة من مصدر المجال الكهريائي عند التقلص العضلي. الاشارة العضلية بصورة رئيسية في مجالين : تشخيص الخلل العضلي واشارة تحكم لسياقة ذراع الي، يستخدم الذراع الالي المساق بواسطة الاشارة العضلي | Electromyogram (EMG) is a signal detected on the skin above a muscle and generated by sources of electric field within the muscle during contraction. EMG signal is used mainly in two fields; Muscle disorder diagnostic and control signal for driving robotic arm. The robot arm driven by EMG is used as a remote control in hazard places or as prosthesis part for limbs of disabled. The first part presents placing array of EMG electrode on two muscles and measure the EMG signal, design acquisition circuit to optimize the EMG signal for two muscles; hardware circuit that designed will eliminate the noise resulting from cable, electrodes, 50Hz and aliasing. In order to monitor and record EMG signal, Data Acquisition System (DAQ) is designed for this purpose using Arduino platform, which gives the ability to deal with signal. The real time signal was taken from three persons with different weights and ages. The second part includes a proposed design of digital filter with windowing and applying to real time signal to compare the results for many times of orders and types of windowing in order to meet the best criteria. The FIR filter with 8th order will be chosen as digital filter with Hann windowing that is apply to eliminate the EMG noise that is caused from many sources and results optimum EMG signal that is used to control robot arm, implementing digital filter characteristic into dsPIC30F4013 which it signal processing microcontroller and using the filtered signal to control the robot arm by interfacing with DC driver to drive robotic arm with two degrees of freedom (2 - DOF). Also, this part includes the technique which simulates the results using MATLAB 2011a to control the movements of the robotic arm. Micro C for dsPIC© is used to write C code for FIR digital filter and loops with control algorithm to enable the controlling robot arm.

تقليل التاثيرات اللاخطية في منظومات التقسيم المتعدد للطول الموجي العالية الكثافة == Mitigation of Fiber Nonlinearity Effects In Ultra High - Dence WDM System

اسم المؤلف: سيف حسام عبد الواحد
اسم المشرف: علي يوسف فتاح
السنة: 2014
الموضوع الدقيق: هندسة الاتصالات
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: The optical signal is severely degraded when transmitted in the fiber due to both the linear and nonlinear distortions. It is well known that, the linear distortions in single mode fiber include chromatic dispersion (CD) and polarization - mode dispersion (PMD) while self - phase modulation (SPM), cross phase modulation (XPM) and four - wave mixing (FWM) are considered the most among nonlinear distortions. To deal with the nonlinear impairments, a number of techniques, such as electronic equalization, pre - coding, digital back - propagation(BP), pre - chirping, optical phase conjugation (OPC) and nonlinearity management, are developed and improved. In the present work, a method called Fractional Fourier Transform (FRFT) has been applied to mitigate fiber nonlinearity impairments. The Fractional Fourier Transform is a time - frequency distribution and an extension of the classical Fourier transform. Time domain FRFT can be implemented by using time lens according to the optical time - space duality theory. The modulated optical pulses will be pre - distorted by an FRFT module before being launched into fiber links. In this work, 10 Gb/s optical fiber system with five spans, each of length 60 Km, for three types of modulation formats (Return - to - Zero Differential Phase Shift Keying (RZ - DPSK), Return - to - Zero Differential Quaternary Phase Shift Keying (RZ - DQPSK) and Carrier - Suppressed Return - to - Zero (CSRZ)), single and multi - channel transmission systems are designed and simulated using “OptiSystem (2011) version 10.0” software package. In order to analyze the transmission performance of the simulated systems without and with FRFT, a set of eye diagrams, optical spectrum visualizers, Q - factor versus input power and Bite Error Rate (BER) versus Signal to Noise Ratio (SNR) curves are presented to evaluate the influence of FRFTon the system performance. For CSRZ modulation format the Q - factor for single channel system at 0 dBm (input power) was 43.5 without FRFT and 78 with FRFT. The BER of sixteen channel system (channel No.8) at bit rate 10 Gb/s per channel, 300 Km link length of CSRZ modulation format with channel spacing of 50 GHz at SNR 10 dB without FRFT is 10 - 4.8 and 10 - 7.4 with FRFT. The BER of thirty two channel system (channel No.16) at bit rate 10 Gb/s per channel, 300 Km link length of CSRZ modulation format with channel spacing of 50 GHz at SNR 10 dB without FRFT is 10 - 4.6 and 10 - 6.4 with FRFT. The BER of thirty two channel system (channel No.16) at bit rate 10 Gb/s per channel, 300 Km link length of CSRZ modulation format with channel spacing of 25 GHz at SNR 10 dB without FRFT is 10 - 2.56 and 10 - 3.24 with FRFT.

خوارزمية جديدة لنظام اخفاء المعلومات == New Algorithm For A Steganography System

اسم المؤلف: مروة جليل محسن
اسم المشرف: اثير علاء صبري
السنة: 2014
الموضوع الدقيق: هندسة الاتصالات
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: This thesis presents a new steganographic algorithm for embedding encrypted secret image in grayscale and color images to provide high level security of data for communication over unsecured channels.The proposed algorithm combine the features of Cryptography and Steganography. The hidden secret message capacity, stego - image quality and security are three important conditions for data hiding technology. According to these requirements, an effective security protection with high hiding capacity steganographic algorithms are proposed based on frequency domain of the cover and the secret image.The proposed algorithm first analyzes the secret image into its frequency components using Discrete wavelet transform (DWT) , Wavelet packet transform(WPT) , Multiwavelet transform(MWT) , and slantlet transform(SLT) , respectively. Then the low frequencycomponent of the secret image is encrypted using Advanced encrypted standard (AES) method and then embedded in the insensitive mid and high sub - bands obtained from the cover image after applying these transformations (mentioned earlier) on it. The embedding method used in this thesis is LSB (Least significant bit ) method. The resulting stego image from different algorithms are then compared..The effectiveness of the proposed algorithm has been estimated by computing Mean square error (MSE) ,signal to noise ratio (SNR), Peak Signal to Noise Ratio (PSNR) and the capacity.The best algorithm is obtained by using 2level - DWT for cover image and 1level - DWT or WPT for secret image because the capacity of the hidden secret data and stego image quality are improved. The embedding image reaches to half the size of cover image at same time PSNR reach to 62 dB and MSE about 0.036 and this is better than many other existence algorithms.By both objective and subjective observations, the resultant stegoimage that will be transmitted does not draw any suspicion, so the main goal of steganography is achieved..The language used for testing the algorithms is MATLAB R2013a, with a computer of the following specification ; Processor : Intel(R) Core(TM) i5 CPU M430 @ 2.27GHz and RAM - 3GBytes.

اخفاء العلامة المائية الرقمية باستخدام تحويل الموجيات ذات عامل جودة قابل للتعديل == Digital Watermarking Based On Tunable Q - Wavelet Transform

اسم المؤلف: هاجر احمد ابراهيم
اسم المشرف: اثير علاء صبري
السنة: 2014
الموضوع الدقيق: هندسة الاتصالات
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: لقد دخلنا عصر حيث المعدات غير المكلفة متوفرة ويمكن من خلالها انتاج نسخ كاملة من المواد المتعددة الوسائط الرقمية مثل صوتيات بجودة القرص المضغوط ونشر صور عالية الجودة او مقاطع الفيديو الرقمية. من خلال هذه البيئة اصبح من السهل على الجهات غير المختصة انتاج ن | We have entered an era where inexpensive and readily available equipment can produce perfect copies of digital multimedia materials, such as CD - quality audio, publication - quality images, or digital video. In this environment, it has become easier for malicious parties to make salable copies of copyrighted content without compensation to the content owner.Many media content owners are concerned about the potential loss of revenue from multimedia piracy, especially when the content will be exposed to the Internet. Digital watermarking is seen by many as a potential solution to this problem.In this thesis, two proposed methods one for grayscale image watermarking and the other for color image watermarking are suggested. They require the original image for watermark extraction and they are belonging to the wavelet domain watermarking. They exploit the Tunable Q_Wavelet Transform. Therefore, different cases are performed to identify the best among them for the proposed application. As a result of the testing process, the best case is founded when ( Q=4, r=8, J=28). The first proposed method can be used with applications requiring high degree of imperceptibility and high security. The embedding process of this method is based on adding the pseudorandom watermark bits in the largest TQWT coefficient.The second proposed method is more robust against distortions than the first proposed method and is characterized by an acceptable degree of imperceptibility and high security. The embedding process of this method is based on adding the compound watermark image to the original color image.They are performed using MATLAB7 programming language. Different images are tested and the watermark is extracted exactly from the watermarked images.The Peak Signal to Noise Ratio “PSNR” using best case for the two proposed methods is found (77.97) dB for the first method and (51.14) dB for the second method.

تحديد منظومة كفوءة للقدرة الفوتوضوئية المستقلة بناءا على الاجواء العراقية == Investigation Into Efficient Stand - Alone Photovoltaic System Based On Iraq Climate

اسم المؤلف: انسام صبحي جبار
اسم المشرف: محمد مؤنس عز الدين
السنة: 2014
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: الطاقة الشمسية هي احدى الطاقات المتجددة التي تمتاز بانها امنة وصديقه للبيئة. عالميا هناك توجه كبير لهذة الانواع من الطاقات للحد من مشاكل التلوث والاحتباس الحراري. شهدت السنوات الاخيرة انخفاض في اسعار منظومات الطاقة الشمسية وكذلك ارتفاع كفائتها مما ساعد وب | Solar energy is safe as well as clean. It is one type of renewable energy , the energy does not cause pollutions and is not harmful to the environment. It is gaining importance now with the increases in global warming and pollution causing the adoption of renewable energy sources as alternative energy sources. For these reasons, the technological advance seeks to reduce the cost of renewable energy and increase efficiency to expand its reach.This work investigates the best strategy for design the solar energy system of stand - alone type. The stand - alone system consists of the PV array, maximum power point tracking, DC - DC converters, charge controller, battery, load and inverter. Standard specifications are used to ensure the successful operation of any system designed according to this method.The proposed method in this work includes calculation by using Microsoft Excel and simulation of long term periods especially during the autonomy days operation by using Matlab/Simulink. Many cases are studied, a suitable PV power system is introduced for each case. The results of the design of the case study are quite in agreement with published results.The objective of this work is to design solar energy systems for hypothetical loads according to Iraqi climate, this aim is achieved because the designed system passed many tests, especially for the worst case of operation. The investigation shows that the system is capable of exhibiting a reliable operation for any weather condition.

تصميم مضخمات قدرة راديوية التردد بتقنية CMOS مع محولات جامعة للقدرة == Design of RF Power Amplifiers With Power Combining Transformers

اسم المؤلف: سهاد حسين جاسم
اسم المشرف: احمد سعدون عز الدين
السنة: 2014
الموضوع الدقيق: هندسة الالكترونيك
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: باستخدام تقنية CMOS، تواجه تكامل مضخمات القدرة العديد من التحديات بمستوى الواط والمستخدمة لتطبيقات الاتصالات اللاسلكية. وللتغلب على هذه المحددات، يمكن استخدام عدد من الوسائل واطئة الفولتية ودمجها بكفاءة باستخدام المحولات على الرقاقة لزيادة قدرة الخرج النا | In CMOS technology, many challenges face the integrated watt level power amplifiers (PAs) used in wireless applications. Consequently, to overcome these limits, several low voltage devices should be combined efficiently with on - chip transformers in order to increase the resulting output power. In this work, two high - performance Radio - Frequency (RF) power amplifiers for watt level applications are designed and simulated in deep submicron (0.13 µm) CMOS process technology using “Agilent Advanced Design System ADS 2011.10 with “BSIM4” as a simulation module for Metal - Oxide - Semiconductor Field - Effect Transistor (MOSFET) devices. The design includes a comparison for the conventional transformer combining techniques SCT, PCT and the hybrid type PSCT. The amplifiers incorporate a parallel combination of four differential PA cores to generate high output power with good efficiency and linearity. The first part of the work presents a design for a watt - level class - AB power amplifier based on transformer type power combiner PSCT for WLAN applications. The PA delivers an Output Power (Pout) of 30 dBm, Power Gain (Gp) of 30 dB and 40% Power Added Efficiency (PAE) under 2.5 V supply. In the second part of the work, a class - E PA based on transformer type power combiner PSCT is designed. The power amplifier provides an output power of 30 dBm, power gain of 30 dB, and 54% PAE at 2.45 GHz under 1.6 V supply. Finally, in the third part of this work, an on - chip output transformer layout for the proposed power amplifiers is designed and simulated with momentum RF EM simulator of ADS 2011.10 in order to realize a fully integrated power amplifier. The simulated efficiency of the PSCT was 78% with minimum insertion losses (ILmin) 0.87 dB.

تصميم متحكم ذكي لنظام تتبع شمسي بالاعتماد على مصفوفة البوابات الرقمية القابلة للبرمجة == Design of Intelligent Controller For Solar Tracking System Based On FPGA

اسم المؤلف: ياسر محمد عبد
اسم المشرف: حنان عبد الرضا عكار
السنة: 2014
الموضوع الدقيق: هندسة الالكترونيك
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: ان الحاجة لزيادة توليد الطاقة الكهربائية جعل استخدام الخلايا الشمسية تلعب دورا هاما في الحياة اليومية، وعليه من المهم استخدام نظام يسمح بتتبع الخلايا الشمسية لضوء الشمس لزيادة او الحصول على القيمة المثلى للطاقة الكهربائية من الخلايا الشمسية. تم في هذا ا | The need to increase the energy generation makes the use of solar cells plays an important role in the daily life. For this reason, it is important to use solar tracking system to increase or getting almost optimum value from solar cells. In this thesis, solar cells model was implemented using MATLAB to show the characteristics of any solar cell depending on data sheet. Intelligent controllers was designed and used to make solar cells facing the sun all days. The proposed controller was trained by two ways; the first was trained by supervised feed forward neural network and the second by Particle Swarm Optimization (PSO) and then comparing the results obtained. The controller was trained using MATLAB and the converting it to simulink model in order to test it, and converts, it to a Very high speed integrated circuit Hardware Description Language (VHDL) language using MATLAB tool box in order to download it on Spartan 3A Field Programmable Gate Arrays (FPGAs) card. This makes the implementation of the intelligent controller more efficient and easy to use because of its reprogram - ability and the high speed performance. The controller was designed to a fully controlled DC motor driver which is used to rotate two DC motors in X - axis and Y - axis directions respectively.The experimental results show that tracking sun increases the efficiency of the system to produce energy from solar cell about 44.3778 % more energy than the solar cell without tracking system.

المسار الامثل للجراحة الروبوتية الطبية باستخدام الخوارزمية الجينية == Path Optimization For Medical Surgery Robotic Using Genetic Algorithm

اسم المؤلف: زهراء داود حسين
اسم المشرف: مهند زيدان خليفة | ايمان صالح كريم
السنة: 2014
الموضوع الدقيق: الهندسة الكهروميكانيكية
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: تناولت هذه الرسالة دراسة تصميم امثل لموديل مختار للانسان الالي المستخدم في مجال الجراحة البشرية (جهاز التنظير البطني الجراحي ) المستخدم في مستشفى الصدر التعليمي في محافظة ميسان والمصنع من قبل شركة (KARL STORZ) من خلال زيادة عدد درجات الحرية لتصل سبعة درج | This thesis presents a study for optimal design of a robot to be used in human surgery (Laparoscope device). It was done in Al - Sader educational hospital in Maysan Governorate. The robot was manufactured by Karl Storz company. Connecting linkages were increased to get seven degrees of freedom. It is operated by the surgeon hand (complete rotation 360o , rotation in two opposite directions perpendicular to each other ,transformation along the major axes , triple joint (pitch ,roll, and yaw). Optimization has been done to these models after making analysis to the surgical robot (forward kinematic, inverse kinematic, dynamitic analysis). The optimal design was obtained by using genetic algorithm method to choose the optimal path planning in the working area. This was with the presence of obstacles to tip of end - effector motion that exists, in mechanical arm to the new model that used in this thesis. This was done by making an integrated computer program through MATLAB (R2013a). The results of best path planning would shorten length without hitting any obstacle, assuming the surrounding environment will be variable. The position and obstacle shapes would be random. We found that the best path planning in every environment depends on maximize objective function that presented by shortest length of the path. This is important from the medical point of view. This was applied successfully in practice on an industrial robot and the resulted optimal parameters to that robot with matching of the theoretical side with practical side in robot motion. The practical side was made in laboratory of the Research Unit of Automation and Robotics in the Control and Systems Engineering Department, University of Technology. The robot used was the Lab - Volt Servo Robot System Model 5250 (RoboCIM5250). This thesis includes studying the tools used in laparoscope and focuses on recent types of graspers with parallel jaws connected to the chosen design. It was noticed that the maximum entrance force for the abdominal tracar must not exceed 5N. The force on the last point of jaws is 0.42N. It was found that this force will not cause bleeding in the tissue during procedure. And that this type of small size grasper can be bent during operation in the allowed field of workspace while maintaining good strength.

نظام كشف وتمييز لوحة الرخصة للسيارات العراقية == License Plate Detection And Recognition System For Iraqi Cars

اسم المؤلف: ثائر عذار هاشم
اسم المشرف: اياد ابراهيم عباس
السنة: 2014
الموضوع الدقيق: هندسة الالكترونيك
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: نظام كشف وتمييز لوحات ارقام السيارات هو تقنية في معالجة الصور يستخدم للتعرف على السيارات من خلال لوحات الارقم الخاصة بها, او بكلمات اخرى هي تقنية تستخدم لتحويل نص صورة لوحة ارقام السيارات الرقمية الى ملف نص ممكن ان يحرر ويستخدم في اي برنامج او تطبيق اخر | Automatic License Plate Detection and Recognition (ALPDR) system is an image processing technology used to identify vehicles by their license plates, or in other words, is a technology used to convert the text on digital images of vehicle license plates to a text file that can be edited and used as such by any other program or application that needs it.License Plate Detection and Recognition system for Iraqi cars have a wide range of applications; it is used to extract plate number to create automated solutions for various problems. Among these applications : parking, border crossing, traffic control, access control and stolen cars tracking.This system consists of two main parts : the first is a practical implementation of how to take a picture automatically for cars passes, this was done by two sensors type (GP2Y0A21YK0F sensor) connected with each other and interfaced with a camera (A4tech USB camera), this camera is interfaced using Matlab with the PC. The camera is attached using USB port. The second part is image processing, this part includes four basic stages : The first stage is image preprocessing which involves image normalization and RGB to gray image conversion. Second stage is detection of a possible license plate using edge detection technique and extracts these LP using region growing technique, detection rates reach to 95%. Third stage is alphanumeric character segmentation to isolate each character, numbers and words of the license plate using Otsu's and Hough transforms technique for subsequent recognition. The last stage reads the alphanumeric character and words by correlation template matching, which is a simple, fast and given a recognition rate reach to 98.245%.

تعزيز اداء اتصالات الراديو عبر الليف احادي ومتعدد الطول الموجي بواسطة تقنية التضمين == Performance Enhancements of Single And Multi - Wavelength Radio Links Over Fiber By Modulation Technique

اسم المؤلف: مصطفى عبد الهادي جليل
اسم المشرف: عايد خلف محمد
السنة: 2014
الموضوع الدقيق: هندسة الاتصالات
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الكلمات الدلالية:
  • Radio - over - Fiber (RoF)
  • Quadrature Phase Shift Keying (QPSK)
  • Quadrature Amplitude Modulation (QAM)
  • Orthogonal Frequency Division Multiplexing (OFDM)
  • Digital Signal Processing (DSP) Unit
الصفحات الاولى:
المستخلص: تم تطوير تكنولوجيا الراديو عبر الالياف منذ اواخر القرن العشرين، وتم استخدامها في مجموعة من التطبيقات لانظمة الاتصالات ويعتبر الراديو عبر الالياف هو الجيل المقبل من انظمة الاتصالات لما يمتاز به من العديد من المزايا مقارنة مع النظام التقليدي مع توهين منخفض | Radio - over - Fiber (RoF) technology has been developed since the late 20th century and has been used efficiently in a range of applications for communication systems. Radio over fiber system is the next generation of communication systems because it has many advantages compared with conventional system with low attenuation, enormous bandwidth of optical fiber, and extension of existing coverage and capacity. RoF system refers to the radio signals which are modulated with optical signal and transmitted over optical fiber link from Central Office (CO) to the Remote Nodes (RNs).In this work, several RoF systems have been designed and simulated with different modulation techniques using commercial software package called “Optisystem v.12”. Furthermore, these systems were compared with each other to check for better performance. These systems are presented as follows : The first system is RoF with Quadrature Phase Shift Keying (QPSK), 16 - Quadrature Amplitude Modulation (16 - QAM), and 64 - QAM schemes with and without OFDM technique. The simulation results of this system show that the Signal to Noise Ratio (SNR) for 64 - QAM - OFDM higher than SNR for QPSK, 4 - QAM and 16 - QAM with OFDM at 10 - 9 symbol error, after 50 km of SMF length without any amplification or compensation techniques. In addition, also SNR for 64 - QAM - OFDM higher than SNR for other techniques in this work after 160 km of fiber length.The second system is the RoF with QPSK and 16 - QAM schemes with Digital Signal Processing (DSP) unit in the receiver side. The simulation results of this system show that the Error Vector Magnitude (EVM) for QPSK scheme with DSP unit is 14.5% and 85.5% without DSP unit after 50 km of fiber length. Furthermore, the EVM for 16 - QAM with DSP unit is 7.5%, but the EVM for the same system without DSP unit is 91%. In addition, the EVM for QPSK with DSP equal to 11.5%, but the EVM for 16 - QAM with DSP equal to 9% after 160 km of fiber length.The third system is RoF system with two multiplexing techniques, 8×10 Gbps WDM - RoF system and 4×5 Gbps SCM - RoF system, have been simulated with 4 - QAM - OFDM, 16 - QAM - OFDM and 64 - QAM - OFDM schemes. The fourth system was to combine the techniques of wavelength division multiplexing (WDM) and subcarrier multiplexing (SCM) to increase the capacity of the system by 20×8 Gbps data rate. The simulation results show that the SCM - WDM - RoF with 64 - QAM gives high SNR compared with SCM - WDM - RoF system with other modulation schemes which have been used in this work.

تحسين الاستقرارية باستخدام التوليد الموزع في شبكة النجف الاشرف الكهربائية == Stability Enhancement Using Distributed Generation In Al - Najaf Al - Ashraf Electrical Network

اسم المؤلف: زيد طارق حسن
اسم المشرف: رشيد حميد الربيعي
السنة: 2014
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: ان عمل وتركيب نظام التوزيع يتغير مع اضافة وحدات التوليد الموزع (DG )، حيث انها تؤثر على خسائر القدرة، الاستقرارية، الفولطية، جودة الطاقة وكميات اخرى، لذلك اختيار الموقع الامثل والحجم وعدد وحدات التوليد الموزع (DG ) ضروري لتجنب التاثيرات السلبية على نظا | The operation and structure of distribution system are changing with the integration of distributed generation (DG), where the DG may have effect on power losses, stability, voltage profile, power quality and other quantities, therefore the optimization of location , size and number of DG are necessary to avoid the negative impacts on electric power system.In this work, the Particle Swarm Optimization (PSO) technique is used to find the optimal number and locations of DG in order to minimize the active power losses. The thermal limit of transmission lines and transformers was studied in cases , with DG and without DG, to detect the lines or transformers which exceed the limit in order to processed it. The voltage stability of distribution network has been investigated, using L index (which aims to detect the vulnerable load buses of an electrical power system). Also the rotor angle transient stability of DG units has been calculated to specify the critical clearing time (CCT) of each circuit breaker in distribution network when one of transmission lines is exposed to three phase to ground fault. The developed algorithm has been verified using two test systems IEEE 33 - bus distribution system and the WSCC 9 - bus test system, furthermore applied to a part of Iraqi distribution network (Al - Najaf Al - Ashraf distribution network). Two softwares are used in this work , the first is Matlab R2013a for implementation of the PSO and voltage stability algorithms while the second software is Power World Simulator 15 for implementation of the thermal limit of transmission lines and transformers, and rotor angle transient stability of DG units.DG contributed significantly to reduce the power losses in Al - Najaf Al - Ashraf distribution network, where there is a reduction by about 96% in active losses. Also DG processed the overload of large substations and the stability of buses in the network.
1 ... 123 124 125 126 127 ... 214