عرض: 25 50 75 100 النتائج

نتائج البحث: 25 من أصل 4,674

تحضير ودراسة الخصائص الفيزيائية والمكانيكية للمادة المرتكبة المحضرة من سيراميك الكودراتيت المدعمة بالنحاس == Preparation and study the physical and mechanical properties of Cu reinforced cordierite ceramic composites

اسم المؤلف: علاء رافد علي
اسم المشرف: انوار حسين علي الفؤادي
الموضوع العام: علوم الفيزياء
السنة: 2014
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: A raw material mixture was used for forming the ceramic matrix cordierite(Cor), was included Iraqi clay (Kaolin Duekhla), Alumina and Talc. Prepare (Cu/Cor) composite, were obtained by addition a fine powder (99.99%) of copper as a reinforcement material, to cordierite ceramic with different percentage ratios (10, 20, 30 and 40) wt%. The temperatures for preparing the composite are (700,800) °C ,and the time of treatment is (1,2) hours respectively. The result of X - ray revealed that the peaks of cordierite phase decreased with increasing the additive amount of copper and slightly increased as temperature elevated from 700 oC to 800oC. Scanning electron microscope (SEM) test was used to observe morphology of blend materials . The comparison results of microphotograph images of cordierite ceramic and (Cu/Cor) composite with 40 wt % Cu , shows that the surface of cordierite sample is uniformly and compactly interference by copper distribution particles led to decreasing the porosity with increasing temperature to 800°C for two hours. The measurement of bulk density and apparent porosity was carried out according to Archimedes method and according to (ASTM) procedure, the results show that the density and thermal conductivity of (Cu /Cor) composite samples increased with increasing copper content ratios up to 40 wt% at the heat treatment (700,800) °C for (1,2) hours respectively. The results of calculation of apparent porosity (Por) and water absorption (%) was shows that, the values were decreased at 800°C more than 700°C ,for two hours more than one hours and at copper content ratio 40% more than (30, 20 and 10) respectively. Vickers micro hardness test is carried out by using "Digital Micro hardness tester VHS 1000. The presence of copper decreases the hardness, in comparison with the untreated ceramic sample(without copper) while the compressive strength increased with the increasing the temperature and copper content ratio from (38) to( 167.8 ) MPa at 800˚C . The addition of copper up to 40% in cordierite matrix lead to decrease of pores and then enhance the densification of (Cu/Cor) composite

التركيب النووي للانوية شديدة التشوه == NUCLEAR STRUCTUER OF STRONGLY DEFORMED NUCLEI

اسم المؤلف: عطاء علي حسن
اسم المشرف: ايمان طارق العلوي
الموضوع العام: علوم الفيزياء
السنة: 2009
الدرجة: ماجستير
اللغة: العربية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: تم خلال البحث الحالي دراسة التركيب النووي للنوى شديدة التشوه ذات الاعداد الكتلية (A=170,174,182) لكل من الانوية الزوجية - زوجية على التوالي، بعد تحديد التناظر الديناميكي SU(3) لكل نواة، باستخدام نموذج البوزونات المتفاعلة الاول (IBM - 1) حيث تم حساب القيم الذاتية والمتجهات الذاتية باستخدام برنامج (IBS1.for) .وتم ايضا دراسة وحساب طاقة جهد السطح لهذه الانوية باستخدام برنامج (PES.for) ورسم الخطوط الكنتورية والتناظرات المحورية لها والخطوط الشبكية المتعامدة والتي اعطت توافقا جيدا مع المخططات المثالية وتركيب الحزم. وقد تم لاول مرة اشتقاق كل من مؤثرات مؤثر دالة هاملتون والزمر الفرعية للزمرة الوحدوية U(6) والاعداد الكمية للحالات الاساسية للتناظر الديناميكي SU(3) وعدد المولدات (ابعادها) باستخدام جبر لي. وتم حساب احتمالية الانتقالات الكهربائية رباعية القطب B(E2) وحساب قيم عناصر المصفوفة المختزلة لمؤثر الانتقال الكهربائي رباعي القطب والعزوم الكهربائية رباعية القطب (QL) وكذلك حساب الانتقالات المغناطيسية ثنائية القطب B(M1) وحساب قيم عناصر المصفوفة المختزلة لمؤثر الانتقال المغناطيسي وقد استخدمت نتائج حسابات المصفوفة المختزلة لمؤثر الانتقال الكهربائي رباعي القطب والمغناطيسي ثنائي القطب في حساب نسب الخلط (E2/M1) للحصول على معلومات اوفر عن التركيب النووي وقد بينت الحسابات الحالية بان مقدار واشارة نسب الخلط لانتقالات مختلفة اعطت توافقا جيدا مع القيم العملية المتوفرة .وقد تم خلال البحث ايضا حساب الطاقة الدورانية لعزم القصور الذاتي ومعامل الليونة وتقاطع الحزم وظاهرة الانحناء باستخدام نموذج (VMI) وعلاقتها بالزخم الزاوي . وقد تم ايضا حساب معدل الجذر التربيعي لنصف القطر النووي r21/2 ومؤثر اعلومة التشوه رباعي القطب ( ( ومؤثر اعلومة الانحراف ( ) اللذان يصفان التشوهات السطحية والمحورية في النواة وكذلك قمنا بحساب العزوم الكهربائية الذاتية رباعية القطب (Q) الذي يعد اعلومة اخرى من اعلومات التشوه المستخدمة في حساب درجة تشوه هذه الانوية اعتمادا على كل من مؤثرات اعلومات التشوه ( ) , وحساب المحاور النووية للشكل الاهليليجي المتطاول او المفلطح لهذه الانوية شديدة التشوه موضوع البحث. لقد تمت كتابة جميع البرامج بلغة فورتران (Fortran 90) بمساعدة البرنامج التشغيلي Compaq Visual Fortran (CVF6.6). وقد قورنت النتائج الحالية مع القيم العملية المتوفرة فكانت متوافقة بشكل جيد في معظمها | In this work, the nuclear structure has been studied for strongly deformed nuclei with mass number (A=170,174,182) for even - even nuclei respectively using the Interacting Boson Model (IBM - 1). The dynamical symmetry SU(3) has been predicated for each nuclei . Derivation of operators of Hamiltonian operator, subalgebra of unitary group U(16), quantum numbers of bases states of SU(3) dynamical symmetry and the number of generators (Dimensions) using using Lie Algebra have been done. Eigen values and eigen vectors have been calculated using (IBS1.for) program. The potential energy surface for each nuclei has been studies and calculated using (PES.for) program, also contour lines, axially symmetries and mesh grid has been drown. The results have been compared with typical scheme and band structure give a good agreement. The electric quadrupole transition probability B(E2), its reduced matrix element < Lf ║ (E2) ║Li > and the electric quadrupole moments (QL). Also the magnetic dipole transition probability B(M1) and its reduced matrix element < Lf ║ (M1) ║Li > have been calculated. The results of the reduced matrix element of electric quadrupole transition operator and magnetic dipole transition operator have been used to calculate (E2/M1) mixing ratios to get more information about the nuclear structure . The results of the present calculation show that both the magnitude and sign (E2/M1) for different transitions for each nuclei are in agreement with the available experimental values. In this research the rotational energy and the moment of inertial, the softness coefficient; the cross bands; the back bending have been calculated for these nuclei and their dependence on the angular momentum using (VMI) Models and (VMI.for) program. The root mean nuclear radius r21/2 , quadrupole deformation parameter operator and the distortion parameter operator have been calculated to describe the surface and axially deformation in each nuclei using (Defo.for) program. The intrinsic electric quadrupole moment which predict the deformation in each nuclei has been calculated to find the degree of deformation depending on the deformation parameters and to calculate the nuclear axis for the ellipsoidal prolate or oblate shape for the strong deformed nuclei. All programs have been written in Fortran 90 with the aid of Compaq Visual Fortran (CVF 6.6) for doing the calculations. The results of the present work are compared with available experimental data, it was in good agreement in most cases.

تمييز الاهداف عن الخلفية الارضية ذات التماثل الحراري في الحزمتين من الاطوال الموجية [3.5 - 4.1 - µm and 11 - 12 - µm ] == Discrimination of targets from background of similar temperature, using two - channel data in the 3.5 - 4.1 - µm and 11 - 12 - µm regions

اسم المؤلف: عدي جواد كاظم
اسم المشرف: بسعاد هادي حمزة
الموضوع العام: علوم الفيزياء
السنة: 2011
الموضوع الدقيق: الفيزياء
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: للتمييز بين هدفين او هدف عن الخلفية الارضية استخدمت طريقتان,طريقة حد العتبة وطريقة التصنيف طريقة الحد الاقصى (MLH). تم حساب ( Wλ ) الانبعاثية الطيفية للهدف والخلفية في درجات حرارة مختلفة(T) في اثنين من الحزم الطيفية وبطول موجي μm (3.5 - 4.1) μm(11.0 - 12.0) . وبرسم العلاقة بين دالة التمييز (DF)كدالة لانبعاثية الهدف (target emissivity (εA)) للحزمة وكدالة لدرجات حرارة الهدف. من هذا العمل, التمييز بين الهدف والخلفية الارضية تحت الظروف الجوية المحددة المستخدمة في الموديل الرياضي للحسابات يبين جدوى امكانية كشف الاهداف المختلفة عن الخلفية الارضية بفارق حراري صغير نسبيا.ان تمييز الاهداف بطريقة الكشف الحراري باللاشعة تحت الحمراء يتم من خلال استخدام طريقة حد العتبة والتي تعالج مشكلة الكشف عن الاهداف التي تكون قريبة لدرجة حرارة المحيط ,وذلك بنمذجة الخلفية وباستخدام الموديل الرياضي كقاعدة لتطوير وفهم العمليات الفيزيائية واختلافاتها الامر الذي سيؤدي الى بناء خوارزمية لتعزيز الفرق بين الهدف والخلفية.وبحساب النسبة بين الاشعاع المستلم من الهدف ومن الخلفية، فان افضل تمييز للهدف يكون في حزمتين من الطول الموجي مما هو عليه الحال في حالة استخدام الحزمة الواحدة وخاصة عندما تكون درجة الحرارة للخلفية الارضية والهدف متماثلة..باستخدام احدى طرق التصنيف وهي طريقة الحد الاقصى لتميــــيز الهدف عن الخلفية الارضية في درجات حرارة مختلفة وحزم اطوال موجية مختلفة ومن خلال ملاحظة اقصى كثافة احتمالية . نستنتج ان طريقة الحد الاقصى هي افضل طريقة لتحسين التمييز في نطاق واسع من حزم الطول الموجي في درجات حرارة مختلفة بينما تكون طريقة حد العتبة اسلوب افضل في تحسين التمييز في درجات حرارة مختلفة ولكن في نطاق ضيق من حزم الطول الموجي | To discriminate between two IR targets or target from background two methods are used, the threshold method and the classification method Maximum likelihood Method. we calculate the spectral radiant emittance Wλ for target and background at different temperature (T) in two bands (3.5 - 4.1) μm (11.0 - 12.0) μm. The discrimination function (DF) is plotted as a function of the target emissivity (εA) for bandpass and as a function to target temperature TA in two bandpasses. From this work the discrimination of target from background under selected atmospheric conditions used in the modeling calculation demonstrates the feasibility of detection for target to background in minor temperature differences. Targets discrimination for thermal IR detection is accomplished by using threshold method, which has addressed the problem of detecting targets which are close to ambient temperature. This was done by modeling the background and by using the model as a base for developing an understanding of physical processes and their variations which will lead to the construction of an algorithm to enhance target to background contrast. The present study showed that by ratioing radiance received from target and background better target discrimination is possible using two bands than case from using one bandpass especially when target and background are of similar temperature. Using the Maximum Likelihood Method (MLH) to discriminate target from background in different temperature and different bands will demonstrate the maximum probability density function. Concluding that the Maximum Likelihood Method is to be the best method for discrimination in wide range of wavelength at different temperatures while the threshold method is to be the best method for discrimination at different temperatures but in range of narrow wavelength of bandpasses.

تصنيع ودراسة خصائص كاشف المفرق الهجين CdO/Porous Silicon

اسم المؤلف: عبد الله محمود علي الجبوري
اسم المشرف: نادر فاضل حبوبي | رائد عبد الوهاب اسماعيل
الموضوع العام: علوم الفيزياء
السنة: 2016
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: في هذا البحث، تم ترسيب اغشيةCdO على السليكون المسامي وعلى شرائح زجاجية بطريقة الاكسدة الحرارية السريعة(Rapid Thermal Oxidation) وذلك لدراسة الخصائص التركيبية والكهربائية والبصرية لهذه الاغشية. تم تصنيع كاشف المفرق الهجين نوع CdO/Porous Silicon من خلال الاكسدة الحرارية السريعة لمادة الكادميوم المرسبة على السليكون المسامي ,تم دراسة الخصائص الكهربائية والتركيبية والفولطائية الضوئية لهذه الكواشف من خللال قياسات تيار - جهد وسعة - جهد. تم استخدام التنميش الكهروكيمياوي للسليكون حيث تمت السيطرة على المسامية بتغيير كثافة تيار التنميش وزمن التنميش. لقد اوضحت النتائج ان معلمات الكاشف تعتمد بشكل كبيركثافة تيار التنميش وزمن التنميش. ان اقل قيمة لعامل المثالية التي تم الحصول عليه كانت 1.28 وذلك للكواشف المصنعة بكثافة تيار40 ملي امبير/سم2 وزمن تنميش 600 ثانية .لقد اوضحت نتائج الكفاءة الكمية اي الكواشف المصنعة تمتلك قمتين الاولى تمتص عند المنطقة المحصورة بين اوكسبد الكادميوم والسليكون المسامي اما المنطقة الثانية ناتجة بسبب الامتصاص عندالسليكون البلوري والسليكون المسامي. قيمة الكفاءة الكمية عند المنطقة الاولى كانت بحدود 77% عند الطول الموجي 550 نانومتر بينما الثانية كانت بحدود 88% عند الطول الموجي 700نانومتر. اعلى قيمة للكشفية النوعية كانت بحدود 87 عند الطول الموجي 550 نانومتر للكواشف المصنعة بكثافة تيار 30 ملي امبير/سم2 وزمن تنميش 2400 ثانية. كل الكواشف المصنعة تعمل للمدى الطيفي ( 400 - 900 ) نانومتر. اعلى قيمة لتياردائرة القصر كانت 19 مايكروامبير واعلى قيمة لفولتية الدائرة المفتوحة 420 ملي فولت للكواشف المصنعة. | In this work, CdO thin films are deposited on porous silicon and clean glass substrates by rapid thermal oxidation (RTO) to study structural, electrical and optical properties of these films. CdO/porous Si heterojunction photodetectors have been fabricated by rapid thermal oxidation (RTO) of Cd on porous and are presented. Structural, electrical, and photovoltaic properties of CdO/P - Si heterojunctions prepared by (RTO) on single - crystal p - type and monocrystalline silicon (111) substrates are examined with J - V the C - V methods. The electrochemical etching process was adopted as a technique to control the porosity of silicon wafer by controlling the time of etching in the range (600 - 2400s), and by controlling the etching current density. The results revealed that all our detectors’ parameters are highly dependant on etching time and etching current density. The minimum value of ideality factor is 1.28 for the detectors prepared with etching current density of 40mA/cm2 for 600s. The results of quantum efficiency show that these detectors have two depletion regions, the first one between CdO film and porous silicon layer, the second between the latter and the crystalline silicon. The first peak of quantum efficiency curve is 77% at a wavelength of 550nm while the second one is 88% at 700nm. The maximum specific detectivity was of wavelength 550nm for the detectors fabricated with etching current density of 40mA/cm2 and etching time of 2400s. All detectors are working on the spectrum region 400 - 900nm. The maximum Isc and Voc are 19A, 420mV respectively for the detectors fabricated with etching current density 30mA/cm2 and etching time 1200s

تصنيع دروع واقية من الاشعاع ودراسة بعض خواصها == Manufacture radiation protection shields and study some of its properties

اسم المؤلف: عبد الرحيم ضياء ابراهيم
اسم المشرف: احمد فاضل مخيبر
الموضوع العام: علوم الفيزياء
السنة: 2016
الموضوع الدقيق: الفيزياء
الدرجة: ماجستير
اللغة: العربية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: تم في هذه الدراسة تصنيع دروع واقية من مواد متراكبة مكونة من الايبوكسي كمادة اساس ومواد تدعيم مختلفة (C, Ni, PbO, Bi) وبنسب تدعيم متباينة % (10, 20, 30, 40, 50) وبابعاد cm (1 X 10 X 10) للوقاية من الاشعاع , ولغرض التعرف على مدى ملائمة هذه الدروع للاستعمال في مجال الوقاية من اشعة كاما, قيست بعض معلمات التدريع مثل معامل التوهين الخطي (μ), والعدد الذري المؤثر (Zeffe), وسمك النصف (X_(1/2)), ومعدل المسار الحر (λ_mean), والثقالة للطاقات KeV (121.8, 344.3, 662, 1773 ,1332, 1408) , بالاضافة الى عامل التراكم عند الطاقة 662 KeV , ولهذا الغرض تم استعمال منظومة كاشف ايوديد الصوديوم NaI (TI) مع مصادر مختلفة Eu - 152, Co - 60, Cs - 137. اظهرت النتائج ان هذه المعلمات تتاثر بتغير نسب التدعيم وطاقة اشعة كاما , حيث تبين ان زيادة نسبة التدعيم للدروع ادى الى زيادة كل من معامل التوهين الخطي والعدد الذري المؤثر. وفي المقابل يحدث نقصان قيم كل منهما خلال زيادة طاقة اشعة كاما للمصدر المستعمل . وبخاصة عند التراكيز العالية % (40, 50), والطاقات الواطئة< 0.662 MeV E_γ حيث سجلت قيم معامل التوهين الخطي cm - 1 (2.1726, 3.6161) للدروع المدعمة بالبزموث بنسبة تدعيم %40 و50% على التوالي ولطاقة 121.8 KeV, ولطاقة 344.3 KeV ولنفس التركيزين ايضا cm - 1 (0.36521, 0.4005) على التوالي, اما عامل التراكم فقد وجد انه يقل بزيادة التركيز عند طاقة معينة. اما بالنسبة لسمك النصف ومعدل المسار الحر فقد وجد ان سمك النصف يقل بزيادة التراكيز وبخاصة عند التراكيز العالية وكذلك الحال بالنسبة لمعدل المسار الحر. كذلك تم قياس قيم الثقالة للدروع كافة بالنسبة لعنصر الرصاص, حيث وجد من خلال قيم الثقالة ان هذه الدروع اخف وزنا من مادة الرصاص, مما يجعلها مفضلة على المواد التقليدية مثل الرصاص والكونكريت. واما بالنسبة لكفاءة الكاشف فقد وجد انها تعتمد في قيمها على مادة الدرع ونوعه وكذلك على قيمة الطاقة المستخدمة. وبينت الدراسة ان هناك توافقا جيدا بين القيم العملية والنظرية. | In this study, protection shields has been preparated , consist of composite materials have epoxy as a basis material and different reinforcing materials (C, Ni, PbO, Bi), with different reinforcing ratios (10, 20, 30. 40, 50) %, and dimensions (1 X 10 X 10) cm to protect from radiation, for examination the suitability of using this shields to protect from gamma ray, some shielding parameters was calculated like Linear attenuation coefficient (μ), Effective atomic number (Zeffe), Half layer thickness (X_(1/2)), Mean free path (λ_mean), and Heaviness for energies (121.8, 344.3, 662, 1773 ,1332, 1408) KeV , in addition to build up factor at 662 KeV, for this purpose sodium iodide system NaI(TI) was used with deferent radiation sources Eu - 152, Co - 60, Cs - 137.The results show that this parameter effected by the reinforcing ratio and gamma ray energy, it was found the linear attenuation coefficient and atomic effective number increases with reinforcing ratio increases, and decreased with energy increasing. Specially with high concentrations (40, 50) % and at low energies E_γ < 0.662 MeV, Since the values of linear attenuation coefficient for shields which reinforcing by bismuth with concentrations (40%,50) was (2.1726, 3.661) respectively for 121.8 KeV, and for energy 344.3 KeV for same concentrations is (0.36521, 0.4005) respectively. The build up factor was found decreased with reinforcing ratio increases, with certain energy.As for the Half layer thickness and mean free path, it was found that the Half layer thickness decreased with energy increasing specially at high concentrations, as well as the Mean free path.Heaviness was calculated too for all shields with respect to lead, from its values, we found that this shields lighter than lead, which make it preferable to traditional material such as lead and concrete.As for the detector efficiency, it was found to be dependent on the type of shield material and the value of used energy which used. This study showed that there is good agreement between the experimental and theoretical values of total attenuation coefficients

تحسين خصائص كاشف ضوئي باستخدام تقنية التنميش الثنائي للسليكون == Improve of photodetecter characteristic using both sides porous silicon technique

اسم المؤلف: عباس كسوب جار الله الخزرجي
اسم المشرف: وسام جعفر عزيز الدجيلي
الموضوع العام: علوم الفيزياء
السنة: 2015
الموضوع الدقيق: الفيزياء
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: الخلاصة تم في هذا البحث دراسة الخصائص الكهربائية والبصرية والتركيبية لاغشية اوكسيد الزنك (ZnO) النقية والمشوبة بالانديوم (In) بنسب مختلفة (1%, 3%) المحضرة بطريقة الرش الكيميائي الحراري, والتي رسبت على قواعد زجاجية وسليكون مسامي بدرجة حرارة (400±10 oC) وبسمك (120±10 nm). قواعد السيليكون المسامي (لجانب واحد وللجانبين) تم تحضيرها بواسطة طريقة التنميش الكهروكيميائيه على رقائق من السليكون (100) .P - Type الكاشف الضوئي (سليكون مسامي/سليكون بلوري/سيليكون مسامي) (PS/c - Si/PS) صنع وحسن بترسيب الاكاسيد الموصلة الشفافة (ZnO/PS/c - Si/PS) و(IZO/PS/c - Si/PS). السيليكون المثقب كان بمسامات دقيقة (pore size > 50 nm) وقطر المسام يتراوح (0.5 - 1 μ m) وزعت المسامات بشكل عشوائي على سطح السيليكون المثقب. الكثافة العالية للمسامات يمكن ان تلاحظ والمسامية تقريبا .(67%) معدل السمك للجانب الامامي (المصقول) (6 μm) وللجانب الخلفي (الغير المصقول) (3 μm) تقريبا. طبيعة السطح للاغشية المرسبة على السيليكون المسامي تكون ذات سطوح خشنة مقارنة مع الاغشية المرسبة على قواعد زجاجية. بينت تقنية حيود الاشعة السينية ان كل الاغشية المحضرة على القواعد المختلفة هي ذات تركيب سداسي متعدد التبلور hexagonal wurtzite)) مع اتجاه تفاضلي سائد(002) ويعرض قمم جديدة اعتمادا على نوع القاعدة كذلك من خلال حيود الاشعة السينية نرى ازاحة في زوايا الحيود وتناقص في الحجم البلوري بسبب التشويب للاغشية المحضرة على قواعد زجاجية من (31.18 nm) الى (12.19 nm). اظهرت صور (AFM) مجهر القوة الذرية طبيعة السطح للاغشية المرسبة على قواعد زجاجية بان الاغشية المشوبة بالانديوم ناعمة ومنتظمة. نعومة الاغشية تتناقص مع تركيز (1%) ثم تصبح اكثر نعومة عند تركيز .(3%) النفاذية كانت عالية جدا للاغشية غير المشوبة والمشوبة بالانديوم لمدى من الاطوال الموجية ( (350 - 850 nm. النفاذية تقريبا (79%) قبل تاثير التشويب ثم تصبح (81 %) مع نسبة تشويب (1%) وتتناقص مع تركيز (3%) الى ( (71% .فجوة الطاقة كانت (3.1 eV),(3.22 eV), (3.21eV) للاغشية (pure ZnO) (IZO 1%) و.(IZO 3%) تتناقص المقاومية (ρᴏ) للاغشية المشوبة في درجة حرارة الغرفة مع زيادة تركيز الانديوم من (1%) الى 3%) ) . نلاحظ من خصائص I - V زيادة التيار الضوئي تحت شرط الاضاءة ونتيجة لزيادة تركيز الانديوم يزداد التيار الضوئي لكل الاغشية. كذلك يزداد التيار تحت شرط الظلام مع زيادة تركيز الانديوم ولكن هذه الزيادة اقل من الزيادة تحت شرط الاضاءة. الاستجابة الطيفية تزداد مع زيادة الطول الموجي لكاشف ضوئي PS/c - Si/PS وتصبح تقريبا (0.69 A/W) عند طول موجي (490), كذلك حسنت الاستجابة الطيفية للكاشف الضوئي بترسيب الاكاسيد الموصلة الشفافة على السيليكون المسامي (ZnO and IZO) بتراكيز انديوم مختلفة. الاستجابة الطيفية لكاشف (ZnO/PS/c - Si/PS) تساوي (0.73 A/W) عند الطول الموجي (385 nm) بينما الاستجابه الطيفية لكاشف (IZO/PS/c - Si/PS) كانت (0.84 A/W) عند الطول الموجي (400 nm). كذلك زمن الاستجابة وزمن الرجوع حسن بترسيب (TCO) . يتناقص زمن الاستجابة من (8 second) لكاشف ضوئي PS/c - Si/PS)) الى (4 second) بترسيب اغشية (IZO) بنسبة تشويب (3%) كذلك يتناقص زمن الرجوع من (6 second) لكاشف PS/c - Si/PS)) الى (2 second) لكاشف (IZO/PS/c - Si/PS). | In this work, structural, optical and electrical properties of have been studied for un - doped and In doped zinc oxide (ZnO) thin films with different indium doping concentrations (1% and 3%) prepared by a chemical spray pyrolysis technique, deposited on glass and porous silicon (PS) substrates at temperature (400±10 oC) with (120±10) nm thickness. The porous silicon substrates (one - side and two - sides) were formed by electrochemical etching of P - type (100) silicon wafers. Photodetector of (PS/c - Si/PS) has been fabricated and improved (ZnO/PS/c - Si/PS) and (IZO/PS/c - Si/PS) by deposited the transmittance conducting oxide (TCO). The porous silicon was macro pores (pore size > 50 nm) and the pore diameter ranging from (0.5 - 1 μ m), which formed by electrochemical etching on p - type (100) silicon wafer, the pores evidently randomly distributed on the porous silicon surface, the high density of pores has been observed and porosity is approximately (67%). The average thickness of front side (polish side) PS was approximately (6 μm) and about (3 μm) of back side (un - polish side). The surface morphology of the thin films deposited on porous silicon was high surface roughness compared with thin films deposited on glass substrates. The X - ray diffraction technique has showed that all prepared films on glass and PS substrates are polycrystalline structures of hexagonal wurtzite with preferential orientation of plan (002) direction and showed the new peaks depend on the substrate type, also from XRD see shifted in diffraction angle and decreased in crystal size by doping for films deposited on glass substrate from (31.18 nm) to (12.19 nm). AFM images showed that the surfaces morphology of deposited films on glass substrates that the IZO films seem smooth and uniform. The roughness of the films decreases with indium concentration 1% and then become very smooth with indium concentration 3%. The transmittance was very high for un - doped ZnO and IZO films within wavelength range (350 - 850 nm). The transmittance about (79%) before the doping effect then become (81 %) with doping concentration (1%) and decreased with doping concentration (3%) about (71%). The energy gap were (3.21eV), (3.22 eV) and (3.1 eV) of (pure ZnO), (IZO 1%) and (IZO 3%) respectively. The resistivity (ρᴏ) of IZO films at room temperature decrease with increasing of indium concentration (1% and 3%) concentrations. I - V characteristics observed the photocurrent increase under the illumination condition and increasing in indium concentration that result to increasing in photocurrent for all films. In the dark condition the dark current also increasing with increasing of indium concentration but this increases less than the increased under illumination condition. The spectral responsivity increased with increasing the wavelength for PS/c - Si/PS photodetector and become about (0.69 A/W) at wavelength (490 nm), also improved the spectral responsivity for the photodetector by deposited the transparent conducting oxide (ZnO and IZO) on porous silicon with different concentration of the indium. The spectral responsivity of (ZnO/PS/c - Si/PS) detector was equal (0.73 A/W) at wavelength (385 nm) while, the spectral responsivity of (IZO/PS/c - Si/PS) detector was (0.84 A/W) at wavelength (400 nm). The response time and recovery time also improved by deposited the (TCO). The response time decreased from (8 second) of PS/c - Si/PS photodetector to (4 second) by deposited IZO films with doping concentration (3%) and recovery time also decreased from (6 second) of PS/c - Si/PS to (2 second) of (IZO/PS/c - Si/PS).

تحضير ودراسة خصائص ZnO : Al على قواعد مختلفه كمتحسس غازي == Preparing and studying characterization of ZnO : Al with different substrates for gas sensor

اسم المؤلف: ضيدان خلف كافي
اسم المشرف: رعد سعدون صبري
الموضوع العام: علوم الفيزياء
السنة: 2013
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: تم في هذا البحث دراسة الخصائص البصرية والكهربائية والتحسسية لاغشية (ZnO) النقية والمشوبة بالالمنيوم (Al) بالنسب (1%,3%) المحضرة بطريقة الرش الكيميائي الحراري, والتي رسبت على قواعد زجاجية وسليكون وسليكون مسامي بدرجة حرارة (773±10oK)., وبسمك (350±10)nm.ولقد تم تحضير السليكون المسامي بواسطة الانوده الكهروكيميائيه على رقائق من السليكون نوع p type (100)بينت فحوصات نمط الحيود للاشعة السينية (XRD) لتشخيص طبيعة تبلور الاغشية المحضرة, حيث اظهرت النتائج ان جميع الاغشية المحضرة ذات تركيب متعدد التبلور من نوع سداسي hexagonal)).مع اتجاهيه (002 ) ومن خلال قياسات ماسح القوة الذرية AFM وقياسات المجهرالالكتروني الماسح SEM تم التعرف على تاثير القواعد المستخدمة على جميع خواص الاغشية, كما تبين من نتائج التشويب ان زيادة التشويب تؤدي الى النقصان في الحجم الحبيبي حيث تناقص الحجم الحبيبي من (39.38) الى (30.22) في حالة التشويب بنسبة 3% اشتملت الرسالة دراسة الخواص البصرية لاغشية اوكسيد الزنك النقية(ZnO) والمشوبة بالالمنيوم (AZO) على دراسة طيف النفاذيه (T᷊) لاغشية المحضرة حيث بينت النتائج ان اعلى نفاذيه تم الحصول عليها هي(85%) عند الاغشية غير المشوبة بينما كانت النفاذيه للاغشية المشوبة( %80) ولمدى اطوال موجيه300 - 900)nm.) , وتبين ايضا ان الامتصاصية بشكل عام تزداد بزيادة نسب التشويب لتصل اعلى قيمة عند النسبه3% بزيادة نسبة التشويب. تم حساب فجوات الطاقة البصرية للاغشية المشوبة وغير المشوبة وتبين ان فجوة الطاقة تقل بزيادة نسبة التشويب الى ان تصل الى اقل قيمة عند نسبة التشويب (3%). وكانت فجوة الطاقة Egتتراوح من(3.3eV)الى(3.1eV) بزيادة نسب التشويب. اظهرت القياسات الكهربائية ان التوصيلية الكهربائية المستمرة تزداد بزيادة نسبة التشويب لتصل اقصى قيمة عند النسبه 3% مع زيادة نسبة التشويب . وبينت القياسات ان الاغشية كافة تمتلك طاقتين للتنشيط (Ea1) و(Ea2) تقل قيمتهما بزيادة نسبة التشويب. كما بينت خصائص( تيار - فولتيه) ان الاغشيه تمتلك عامل مثاليه (2.3) للاغشيه المرسبة على السيلكون و(1.28) للاغشيه المرسبه على السيليكون المسامي . اما خصائص التحسسية لجميع الاغشية المحضره كانت تقاس بعد تعريضها الى( (750 ppm من بخار الايثانول والميثانول عند درجة حراره 473K. النتائج العملية بينت ان اغشية اوكسيد الزنك المشوبة بالالمنيوم والمرسبة على قواعد زجاجية وشرائح من السليكون وسليكون مسامي تحسن التحسسية لتلك الاغشية لبخار الايثانول والميثانول كما تبين ان افضل نتيجة سجلت كانت لاغشية AZO/PS المشوبة بنسبة 3% حيث كانت (37%) لبخار الايثانول و(35%)لبخار الميثانول بالاضافة الى ذلك تبين ان التحسسية لها علاقة نسبية لدرجات الحرارة وكمية الغاز. | In the present work, structural, optical, electrical and sensing properties have been studied for undoped and Al doped zinc oxide (ZnO) thin films with different aluminum doping concentrations (1% and 3% ) prepared by a chemical spray pyrolysis technique, deposited on glass, silicon, and porous silicon substrate at temperature (773±10)oK with (350±10)nm thickness, The porous silicon (PS) substrates were formed by electrochemical anodization on p - type (100) silicon wafer. The X - ray diffraction technique has showed that all prepared films are polycrystalline structure type of hexagonal wurtzite with preferential orientation of plan (002) direction .Surface analysis by SEM and AFM have been used to understand the effect of the substrate on morphology properties of the samples. The doping resulted in decreasing grain size i.e deteriorates the crystallinity of the films from (39.38nm)of pure ZnO to (30.22nm) of AZO(3%) doped. The measurements of optical properties transmittance of undoped and Al doped ZnO films show that higher transmittance was (85%) for undoped ZnO films while (80 % ) for doped Al films within wavelength range (300 - 900nm). Also the results have showed that absorbance increases with doping to reach maximum value at 3% concentration .The energy gap of ZnO was calculated for undoped and doped films .It is noticed that the energy gap decreases with the increases of doping until it reaches the minimum value at 3% doping concentration . The results of electrical properties have showed that direct current (D.C) conductivity increases by increasing doping to reach maximum value at 3% doping concentration. The results have showed that the films have two activation energy Ea1 and Ea2 . from I - V characteristics it's found that the minimum ideality factors (n =2.3) for AZO/Si and (n=1.28)for AZO/PS of the prepared heterojunction are observed in the interim bias voltage range. The sensing properties for all undoped and doped films were measured after films surface was exposed to 750 ppm from vapor ethanol and methanol gas at temperature of 473ºK . The experimental results of Al doping of zinc oxide thin films with different aluminum doping concentrations (1% and 3% ) which deposited on glass, silicon, and porous silicon substrate showed a good sensitivity to ethanol and methanol vapor. Also the influence of variation of Al concentration and type substrate on ethanol and methanol vapor sensitivity of thin film sensor elements was investigated in this work. Therefore , doping percentage ZnO : Al/PS of 3% concentration recorded the best result 37% for ethanol , 35% for methanol, thus the AZO/PS films are a good sensor for ethanol and methanol vapors. In addition ,the sensitivity is directly proportional with the operation temperature for limited range. In general the sensitivity increases by increasing the concentration of ethanol and methanol vapors with increasing temperature degree

دراسة الصفات الحرارية والميكانيكية وعمر الاداء PVC لبوليمر == Study of the Thermal, Mechanical Properties and Lifetime of PVC Polymer

اسم المؤلف: صهيب صباح احمد
اسم المشرف: وداد حمدي جاسم | محمد عبد النبي ثجيل
الموضوع العام: علوم الفيزياء
السنة: 2015
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: In this work, mechanical behavior of PVC product like pipes with different origins (K.S.A and Egypt) and Turkey doors with different manufacturing (Nova and Firat) which are used in Iraqi markets were studied.The objective of this work was to study the mechanical properties like ultimate tensile strength, Young's modulus, elongation at Max., elongation at break, impact strength, flexural strength and hardness of the pipes and doors.The experimental results show that K.S.A pipes exhibited maximum ultimate tensile strength and Young's modulus than that the Egypt pipes.However, the Egypt pipes exhibited maximum elongation at Max. and elongation at break when compared with K.S.A pipes.All the tensile properties of Firat doors are greater than that of Nova doors.Comparison of the flexural strength of pipes and doors. The pipes have the same flexural strength but the Firat doors have maximum value than Nova doors.Egypt pipes have a higher impact strength than K.S.A pipes. While the Firat doors have a higher impact strength than Nova doors. The experimental results of hardness Shore D indicated that K.S.A pipes exhibited maximum hardness number (83.7) than Egypt one, while the Firat and Nova doors have the same values.In this study, thermal properties of Firat and Nova have been evaluated, firstly by thermal conductivity and second by thermal stability and degradation. The Firat doors have better thermal conductivity than that of Nova doors. From the thermogravimetric analysis at different heating rates (2, 5, 10, 20 and 40 °C/min). The Firat doors have a higher thermal stability than Nova one.The Egypt pipes exhibited more thermal stability than the K.S.A pipes.From the TGA curves the activation energy of pipes and doors are determined at different conversion levels. At 30% conversion level when the mechanism of degradation would be stable and the value of activation energy of Egypt pipes and Firat doors is (108.35 KJ/mole) when it is (101.39 KJ/mole) for K.S.A pipes and (98.35 KJ/mole) for Nova doors. Thermogravimetric analysis (TGA) provides a method for accelerating the lifetime testing of polymers so that short - term experiments can be used to predict in use lifetime.The lifetime is decreased with increase of the temperature, at fixed temperature like 70 °C the lifetime of Egypt pipes is (≈100 years) while lifetime of K.S.A pipes is (≈21 years). At the same temperature (70 °C) the lifetime of Firat doors is (≈72 years) while the lifetime of Nova doors is (≈21 years).Thermomechanical analysis (TMA) test showed the glass transition temperature (Tg) and softening point (Ts) for pipes and doors. The K.S.A pipes have value for Tg and Ts higher than that of Egypt pipes, while the Firat and Nova doors have the same values.

التركيب المورفولوجي والخواص البصرية لاغشية In2O3 الرقيقة == Morphology Structural and Optical Properties of In2O3 Thin Films

اسم المؤلف: شيماء احمد كاظم
اسم المشرف: علية عبد المحسن شهاب
الموضوع العام: علوم الفيزياء
السنة: 2016
الدرجة: ماجستير
اللغة: العربية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: يتناول هذا البحث دراسة تاثير تغير زمن الاكسدة ودرجة حرارة التلدين على الخصائص التركيبية والبصرية لاغشية اوكسيد الانديوم الثلاثي (In2O3) الرقيقة التي تم تحضيرها بتقنية التبخير الحراري في الفراغ ، حيث تم ترسيب معدن الانديوم (In) على قواعد من الزجاج واخرى من السليكون بدرجة حرارة الغرفة (300 K) وبسمك (400 ± 10 nm) وبمعدل ترسيب 5.47 ± 0.5 nm/sec)) ، ومن ثم اكسدة اغشية (In) المحضرة حراريا بدرجة حرارة (673 K) وبوجود الهواء وبزمن مختلف (ساعة ، ساعة ونصف ، ساعتان) ، بعد ذلك تم اجراء التلدين بدرجات حرارة مختلفة K (323 , 373 , 423) على اغشية (In2O3) المؤكسدة بزمن ساعة واحدة باعتبار ان هذا الزمن هو افضل زمن اكسدة من ناحية قيم فجوة الطاقة البصرية والحجم الحبيبي والخشونة ومعدل الخشونة . درست الخصائص التركيبية للاغشية المحضرة (قبل التلدين وبعده) عن طريق تقنية حيود الاشعة السينية (XRD) التي اظهرت ان هذه الاغشية ذات تركيب بلوري متعدد ومن نوع مكعب ، وكذلك تم استخدام مجهر القوة الذرية (AFM) والمجهر الالكتروني الماسح (SEM) لدراسة طوبوغرافية السطح من ناحية التجانس والخشونة ومعدل الخشونة . درست الخصائص البصرية للاغشية المحضرة (قبل التلدين وبعده) باستخدام المطياف البصري (Optical Spectrometer) ، حيث تم حساب فجوة الطاقة البصرية والتي كانت ذات قيمة اقل عند زمن اكسدة ساعة وعند درجة تلدين (323 K) ، بالاضافة الى دراسة طيف كل من الامتصاصية والنفاذية والانعكاسية ، وايضا تم حساب الثوابت البصرية وهي : معامل الامتصاص ، معامل الانكسار ، معامل الخمود ، ثابت العزل بجزئيه الحقيقي والخيالي كدالة لطاقة الفوتون ، وقد بينت النتائج ان زيادة قيم هذه الثوابت متعلقة بزيادة زمن الاكسدة ودرجة حرارة التلدين. | This research examines the effect of changing time of oxidation and the degree of annealing temperature on the structural and optical properties of membranes dioxide triple indium (In2O3 thin) that was prepared technology thermal evaporation in a vacuum, where the deposition of metal indium (In) on the glass and silicon substrate at room temperature (300 K) and thickness (400 ± 10 nm) and the rate of deposition of (5.47 ± 0.5 nm / sec) , and then oxidation films (In) prepared thermally and the presence of air at a different (hour, hour and a half, two hours) , then annealing was performed at different temperatures (323, 373, 423) K films (In2O3) oxidizing a time of one hour, considering that this time is the best time of antioxidants in terms of optical energy gap and grain size and roughness values and the rate of roughness . Structural properties of prepared films have been studied (before and after annealing) by X - ray diffraction technique (XRD) which showed that these films with the structure of crystalline multi it cubic type, as well as the use of an atomic force microscope (AFM) and electron microscopy scanner (SEM) to study the topography of the surface in terms of homogeneity and roughness and the rate of roughness . Optical properties of prepared films have been studied (before and after annealing) using the optical spectrometer, where the optical energy gap , and which were less valuable when oxidation hour time account and at a temperature annealing (323 K) , in addition to the study of spectrum both absorbance and transmittance and reflectivity , and was also the optical constants account : the absorption coefficient, refractive index, extinction coefficient, dielectric constant real and imaginary as a function of photon energy, the results have been shown to increase the values of these constants related to increased oxidation time and the annealing temperature.

تحديد مديات الاجسام وابعادها الغاطسة في الماء باستخدام تقنيات معالجة الصورة الرقمية وتحديد موديل رياضي لمعامل انكسار السوائل الشفافة == Under water objects range and dimensions using digital image processing technique and determine the depths as a function of camera viewing angle

اسم المؤلف: سماهر وحيد هاشم
اسم المشرف: علي عبد داود الزكي
الموضوع العام: علوم الفيزياء
السنة: 2014
الموضوع الدقيق: معالجة الصور
الدرجة: ماجستير
اللغة: العربية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: انتشرت انظمة قياس ابعاد الاجسام الغاطسة في الماء التي تعتمد على استخدام الكاميرا الرقمية على نحو واسع في الاونة الاخيرة , وعلى وجه الخصوص في الانظمة الروبوتية , لقلة تكلفتها ,وسهولة تركيبها , وسرعتها , وكونها امنة ودقيقة بما يكفي مقارنة بانظمة القياس المعقدة الاخرى ، التي تستخدم الليزر او المتحسسات الكهرومغناطيسية . لذلك توجهنا في دراستنا الحالية الى استعمال كاميرراقمية في تحديد طول الجسم بالبكسل Lp وايجاد موديل رياضي لطول الجسم بالبكسل Lp كدالة لعمق الجسم الغاطس في الماء h . وبعد حساب معامل التكبير m للاجسام الغاطسة في الماء ، تم الحصول في هذه الدراسة على موديل رياضي يربط بين معامل التكبير m وعمق الاجسام الغاطسة في الماء h وزاوية التصوير في الكاميرا θ , ومن خلاله تم حساب عمق الجسم , واظهرت النتائج تطابقا عاليا بين القيم الفعلية والقيم المستنتجة من الموديل الرياضي . اما في الحالة الثانية فقد تم ايجاد ابعاد الاجسام الغاطسة في الماء , حيث تم استحداث موديل رياضي يربط بين عامل التدرج Scf وعمق الجسم الغاطس في الماء h وزاوية التصوير للكاميرا θ ومن هذا الموديل الرياضي يمكن ايجاد اي واحد من المعاملات الثلاثة في حال كون اثنين منها معلومة , وقد تم اختبار الموديل لايجاد عمق الجسم الغاطس في الماء وكذلك ايجاد ابعاد الاجسام المجهولة الغاطسة في الماء والنتائج التي تم الحصول عليها كانت قريبة جدا من القيم الحقيقية. كما تم حساب معامل التكبير m وعامل التدرج Scf لايجاد علاقة رياضية تربط بين معامل التكبير وعامل التدرج وزاوية التصوير في الكاميرا لحساب معامل التكبير. وقد عني الجزء الاخير من هذه الدراسة بحساب معامل الانكسار البصري اذ تم اقتراح طريقة جديدة وسريعة وفعالة في تحديد معامل انكسار السوائل ضمن مدى الاطوال الموجية المرئية , اذ حددت العلاقة بين طول الجسم بالبكسل Lp مع العمق الظاهري للجسم الغاطس في السائل hi في حال معرفة معامل انكسار السائل (الماء) , ثم ايجاد علاقة رياضية يمكن اعتمادها كموديل رياضيا فعالا في تحديد معامل انكسار اي سائل شفاف اخر ، حيث تم تطبيق هذا الموديل لحساب معامل انكسار سائل اخر (البنزين) باعتماد المعادلة نفسها في حالة غمر الجسم نفسه فيه . وقد اظهرت النتائج دقه عالية في عملية حساب معامل الانكسار , واظهرت تطابقا بين القيمة الفعلية والقيمة التي تم حسابها في التقنية المقترحة وبنسب خطا ضئيلة جدا. | The measuring systems of dimensions of the immersed objects in water that base on the using of the digital camera are widely spread nowadays, especially in the robotic systems, because they are easy to install, fast, safe, inexpensive, and sufficiently accurate as compared with other complicated measuring systems that using the laser or electromagnetic sensors. Therefore, in the current study we intended to use a digital camera to determine the length of object in Pixels (Lp) and to find mathematical model of the length of the object in Pixels as a function to depth (h) of the immersed object in water. In this study, after calculating the magnification factor (m) of the immersed object in water, we have obtained a mathematical model relates the magnification factor (m) with the depth of the immersed object in water (h) and the angle of the taking picture (θ), then we have calculated the depth of the immersed object, the results showed a high matching between the actual values and the calculated values from this mathematical model. In the second phase of the study we have found the dimensions of the immersed objects in water by developing a mathematical model relates the scale factor (Scf) with the depth of the immersed object in water (h) and the angle of the taking picture (θ), from this mathematical model we can find any one of these parameters in case two of them are known. We have tested this mathematical model to find the depth of immersed object in water and to determine the dimensions of the unknown immersed objects in water. The results were very close to the actual values. Then we have calculated the magnification factor (m) and the scale factor (Scf) to find a mathematical relationship that relates the magnification factor with the scale factor and the angle of the taking picture to calculate the magnification factor. The last part of this study focuses on the calculation of the optical refractive index, where we have proposed a new, fast, and effective method to determine the refractive index of the liquids within the range of the visible wavelengths. We identified a relationship between the length of object in Pixels (Lp) and the apparent depth of the immersed objects in the liquid such as (water) (hi) in case of value of refractive index was known. Then finding mathematical relationship can be adopted as an effective mathematical model to determine the refractive index of another transparent liquid. According to this equation, we have calculated the refractive index of benzene in case we have immersed the same object in it. The results showed high accuracy in the calculating the refractive index, and also showed a symmetry between the actual value and the calculated ones with a very low error rate in the proposed technique.

تصميم وتقييم طلاء المضاد للانعكاس غـير المسـتقطـب == Design and Evaluation of Non - Polarizing Antireflection Coating

اسم المؤلف: سارة عامـر ســــلمان
اسم المشرف: الاء نزار عبد الغفار
الموضوع العام: علوم الفيزياء
السنة: 2016
الدرجة: ماجستير
اللغة: العربية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: لقد تم اجراء دراسة نظرية ووضع نموذج رياضي يعتمد في بناءه على المصفوفة المميزة المعدلة لتصميم طلاء مضاد للانعكاس لايتاثر بالاستقطاب ودراسة تاثير زوايا السقوط المائل . حيث توصلنا الى بنى تصاميم مثلى لطلاءات مضادة للانعكاس غير مستقطبة ولزوايا سقوط مختلفة للطيف الكهرومغناطيسي باستخدام مواد متجانسة موحدة الخواص مهملة الامتصاص ضمن منطقتي الضوء المرئي (300 - 800)nm وتحت الحمراء المتوسطة (3000 - 5000)nm وباستخدام الزجاج والسليكون كمواد اساس على التوالي.وفقا لاجراءات تحقق الامثلية فان النتائج اشارت الى امكانية التغلب على الصعوبات التي تظهر نتيجة السقوط المائل للطيف والتي من ابرزها ظاهرة الفصل (Splitting) لموجة الضوء المنعكسة الى مستويين P, S (نتيجة لظاهرة الاستقطاب) وايضا الازاحة الجانبية لمنحنيي الانعكاسية RS,RP باتجاه الاطوال الموجية القصيرة واللاتناظر بين المنحـنيين .وقد اظهرت التصاميم مقدرة عالية في تقليل انعكاسية الزجاج (ضمن منطقة الطيف المرئي) والسليكون (ضمن منطقة تحت الحمراء المتوسطة ) وتحقيق ادنى انعكاسية عند طول موجة التصميم المقترحة ولمدى واسع من زوايا السقوط. كما اوضحت النتائج امكانية التوصل الى تصميم طلاء مضاد للانعكاس غير مستقطب واسع الحزمة عند زوايا سقوط عالية تصل الى 60o وبعدد طبقات قليلة في المنطقة المرئية, فضلا عن التوصل الى تصميم طلاء مضاد للانعكاسية غير مستقطب عند اطوال موجية مختلفة عند 80o في المنطقة الحمراء | In this current study a mathematical model was put on to design anti - reflection coatings at oblique incidence of light for visible region (300 - 800 )nm and mid infrared region (MWIR) (3000 - 5000)nm .successfully we achieved designs with optimal performance at high angles of incidence where the results refer to overcome significant problems of design at oblique incidence .the main problem that we were able to overcome, is the splitting of the incident light into two modes of wave S and P - polarization where the separation of reflection performance for both S - and P - polarized wave expands when incidence angle increases. We managed to obtain designs of non - polarized antireflection coatings those that have the same reflection for both S - and P - polarizations at specified angles. results refer to designs of non - polarized antireflection coatings without splitting at high incidence angles. We accomplished designs of non - polarized antireflection coatings that provide low reflection within the Intended range of wavelengths where we could to limit the effect of the high incidence angles that increase the reflectance of the chosen substrates.Also the problem of shifting of reflection performance toward shorter wavelengths due to the oblique incidence of light was resolved and designs of optimal performance of non - polarized antireflection coatings with low reflection at high incidence angles was achieved.It has been provided a promising coating materials system for use in design of non - polarizing antireflection coatings at different incidence angles for the concerned wavelengths regions

الخصائص التركيبية والالكترونية لشرائط نانوية من الفسفورين المطعم باستعمال حسابات المبادئ الاساسية == Structural and Electronic Properties of Doped Phosphorene nanoribbons using First - Principle Calculations

اسم المؤلف: سارة جليل احمد
اسم المشرف: حمد رحمن جبر
الموضوع العام: علوم الفيزياء
السنة: 2016
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بابل
الصفحات الاولى:
المستخلص: The doping effect of boron, aluminum, and carbon on black and blue phosphorene nanoribbon (PNRs) is investigated using density functional theory (DFT) in the framework of Perdew, Burke, and Ernzerhof (PBE) functional with 6 - 31G basis set. The effect of doping on the total energy, band gap, ionization potential, electron affinity, Fermi energy, highest occupied (EHOMO) and lowest unoccupied molecular orbital (ELUMO), and density of state have been studied. The results show that the values of the ionization potential, electron affinity and Fermi energy for pristine black PNRs are larger than those of pristine blue PNRs. Also, the energy gap for pristine blue PNRs is slightly smaller than those of pristine black PNRs. In general, the pristine PNRs is a semiconductor with energy gap of blue phosphorene )0.0184( and energy gap of black phosphorene (0.0185) eV. Our results indicate that the highest value of EHOMO is for black phosphorene ( - 5.60eV), these values show that a propensity of phosphorene to donate electrons and smaller value of ELUMO is for blue phosphorene ( - 5.58eV), these values show that a propensity of the phosphorene to accepter electrons. We found that the doping of phosphorene nanoribbon with boron and carbon leading to increase in the energy gap, and the increasing in black phosphorene is very small. On the other hand, the energy gap of aluminum doped phosphorene are smaller than those of pristine for black phosphorene while the energy gaps of aluminum doped phosphorene are larger than those of pristine for blue phosphorene. In the aluminum doped phosphorene, the highest of peaks becomes less, the conduction and valence bands are less with the highest number of density of states. The results also show fluctuations in the converged energy gap and valence bandwidth of black and blue phosphorene due to shape variation. Finally, it is concluded that band gap of phosphorene nanoribbon depends strongly on the type of addition

دراسة تحليلية للحام بالليزر على الخواص الحرارية - الميكانيكية للبوليمرات باستخدام برنامج ANSYS == Analysis Study of Laser Welding on Thermal - Mechanical Properties of Polymers Using ANSYS Program

اسم المؤلف: زينه يونس علي
اسم المشرف: خالد هادي مهدي العبيدي | ندى فاضل توفيق
الموضوع العام: علوم الفيزياء
السنة: 2015
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: الخلاصةان الهدف من هذه الدراسة, هو التنبؤ بسلوك المواد من حيث الخصائص التركيبية ,الحرارية والميكانيكية اثناء عملية اللحام في 3 - D. ان دراسة الخصائص التركيبية للمادة قد تم باعتبارها دالة لدرجة حرارة الانتقال الزجاجي T_g, ودرجة حرارة الانصهار T_m, وتغير الطور بينما يتم دراسة الخصائص الحرارية وفقا لتوزيع درجات الحرارة, والتدرج الحراري, والفيض الحراري, واخيرا يتم دراسة الخواص الميكانيكية بواسطة الاجهاد والمطاوعة.لقد تم تبني طريقة FEM لمحاكاة عملية اللحام لقطعتين متشابهتين ومختلفتين من مادة البولي بروبلين والبولي ستيرين في ثلاثة ابعاد. ان تحليل الخصائص الحرارية والميكانيكية لبوليمر البولي بروبلين والبولي ستيرين قد تم بدلالة كل من نموذج الحالة المستقرة والنموذج المتنقل باستخدام برنامج ((ANSYS 11. حيث ربط نموذج الحالة المستقرة (اعتبرت انها الحمل الابتدائي) مع نموذج الحالة المتنقلة بافتراض وجود الحمل الحراري والميكانيكي سوية بنفس الوقت على اعتبار ثبوت سرعة اللحام عند20ملي/ثانية ودرجة الحرارة عند 298م, وكذلك تم اختبار تاثير قدرة الليزر باستخدام ثلاثة قيم 50) (150,100 واط, كذلك درست تاثير نصف قطر بقعة الليزر على خصائص البوليمرات المستخدمة.بينت النتائج العددية قابلية لحام كل من المادتين البولي بروبلين والبولي ستيرين بهذه الطريقة, حيث لوحظ تناقص التشوهات الحرارية والميكانيكية الناجمة عن اللحام, كما يشير الشكل الهندسي هذه الاجهادات الى جودة اللحام. وبينت الدراسة ان كل من الفيض الحراري والانحدار الحراري يكون عند اعظم قيمها في اتجاه y - axis وهو اتجاه تسليط الليزر, وكانت درجة الحرارة العظمى في لحام كل من PP - PPو PP - PS هي ((351.4kو (425.9k) على التوالي. اما الاجهادات الميكانيكية فقد كانت واطئة في كل من PP - PPو PP - PS بحدود (0.181*〖10〗^9MPa ) و(0.166*〖10〗^9MPa) والمطاوعة (0.171) و(0.142) لكل من PP - PP وPP - PS على التوالي. واخيرا، لوحظ صغر مساحة المنطقة المتاثرة حراريا اذ كانت بحدود (9.2 〖mm〗^2) بالنسبة ل PP - PP، في حين اظهر عمق الاختراق تحسن مقارنة مع الاساليب المستخدمة، حيث كانت قيمته بحدود (2.5mm), اما في نموذج المتنقل فقد لوحظ تضاعف المساحة المتاثرة وعمق اختراق قريب من نتائج النموذج المستقر. | The aims of this study is to estimate the material behavior properties in terms of its structure, thermal and mechanical properties during welding process in 3 - D. The structure is studied as a function of T_m , T_g and phase change. While the thermal is investigated according to thermal distribution, thermal gradient and thermal flux. Finally the mechanical is examined by stress and strain.Finite element method is adopted to simulate welding process of two similar and dissimilar pieces of polypropylene and polystyrene in 3 - D.The analytical of thermal and mechanical properties is done in terms of steady - state model and transient model using ANSYS 11 program, then coupling the steady - state with transient model by supposed existing thermal and mechanical loads together in same time. Laser power effect on welding is investigated by three powers (50,100,and 150watt) and by laser spot radius (1mm, and 2mm), the welding speed is supposed constant at (20mm/sec).Numerical results show that the ability of this method to joined polymers material PP and PS, where it is noticed that the thermal and mechanical deformations are reduced, also the geometry shape of welding zone is indicated to a good quality of welding.From this study, the thermal gradient and thermal flux are at their maximum values at y - axis, in which the laser direction, and T_max in PP - PP and PP - PS joints are (351.4k) and (425.9k) respectively. Mechanical stresses and strains had low values, about (0.181*〖10〗^9MPa) and (0.166*〖10〗^9 MPa) and strain are about (0.171) and (0.142) for PP - PP and PP - 1PS joint respectively.Finally, it is observed that narrow HAZ area (9.2〖mm〗^2) of PP - PP joint, while penetration depth shows improvement comparing with usual methods, it's value is (2.5mm). In transient model it observes that multiples of HAZ area, and D_p is near its value in steady - state model.

دراسة تاثير خطوط الضغط العالي على تراكيز غاز الرادون في الهواء باستعمال كاشف الاثر النووي CR - 39 == Study of The Effect of High Voltage Power Lines on Radon Concentrations in Air Using Solid State Nuclear Track Detector CR - 39

اسم المؤلف: زينة جميل رحيم عبد علي
اسم المشرف: خالد هادي مهدي العبيدي | ندى فاضل توفيق
الموضوع العام: علوم الفيزياء
السنة: 2009
الدرجة: ماجستير
اللغة: العربية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: يتضمن الهدف من البحث دراسة تاثير خطوط الضغط العالي 132kV)و400kV ) في مناطق منتخبة من مدينة بغداد على تراكيز الرادون ونواتج انحلاله باستعمال كاشف الاثر النووي CR - 39. تم توزيع عدد من الكواشف بابعاد (2x1cm²) ولمدة شهر كامل داخل وخارج محطتي بوب الشام 400kV والوزيرية 132kV , كذلك في عدد من الدور السكنية القريبة من خطوط الضغط العالي 132kV ومحطة المعري 132kV القريبة من منطقة العدل ببغداد خلال فصل الخريف. تم تحديد تراكيز الرادون خلال المقارنة مع العينات القياسية، ومن خلال النتائج المستحصلة كانت قيمة المعدل الموزون لتراكيز الرادون داخل الابنية تحت تاثير خطوط الضغط العالي 400kVهي 91.77±0.1122Bq/m³)) وفي الخارج كانت مساوية الى (125.73± o.117 Bq/m³) وتحت تاثير خطوط الضغط العالي 132kV في الداخل كانت مساوية الى 60.03± 0.266 Bq/m³)) اما في الابنية البعيدة عن خطوط الضغط العالي فقد كانت مساوية الى Bq/m³) 23.265± 0.77) وفي خارج الابنية 13.63± 0.99 Bq/m³)) يتضح خلال نتائج الدراسة ارتفاع تراكيز غاز الرادون في المناطق القريبة من خطوط الضغط العالي وبشكل ملحوظ مقارنة مع المناطق البعيدة عن الخطوط مما يدل على ان هناك تاثيرا واضحا لخطوط الضغط العالي على تراكيز غاز الرادون ويزداد هذا التاثير بزيادة شدة المجال الكهرومغناطيسي والقرب من هذه الخطوط, كما كان لخطوط 400kV تاثير اقوى من خطوط 132kV على تراكيز الرادون في الهواء, اما تراكيز غاز الرادون داخل الابنية فكانت اعلى من تراكيزه خارج الابنية , وهذه الزيادة في التركيز تعود الى ان جدران الابنية تعد المصدر الرئيس لتوليد الرادون داخل الابنية , حيث تبين ان مواد البناء قد ادت دورا مهما في زيادة تراكيز غاز الرادون داخل الابنية بالاضافة الى عمر الابنية والارتفاع عن مستوى سطح الارض . | The aim of this research the study of the effect of high Voltage power lines (400kVand132kV) upon radon concentration and its decay results by using nuclear track detectors CR - 39 inside Baghdad city. A number of detectors with the dimensions (2x1cm2) was scattered for a whole month indoor and outdoor Bob Al - sham station 400kV and Al - waziriya station 132kV as well as in number of the houses which are very close from the high voltage power lines 132kV and Al - maary 132kV during autumn. The concentrations of radon were determined through the comparison with the standard samples , The results shows that the value of Weighted Average of radon concentration indoor the buildings which are under the effect of high voltage 400kV is (91.77 ± 0.117Bq/m3) and under the effect of high voltage lines 132kV indoor is equal to (60.03±0.266Bq/m3) ,As for the buildings which are far away from the high voltage lines , it was equal to (23.2651± 0.773Bq/m3) and outdoor the buildings (13.63±0.99 Bq/m3) . The results showed that increase of radon concentration in the areas which are close to high voltage power lines compared with areas which are far away from the lines which show that there is a clear effect of high voltage power lines upon the concentration of radon . And this influence increases with increase of the intensity of electromagnetic field as well as the near distance with these lines .For there was a stronger effect of 400kV lines than 132kV lines upon radon concentration in air, Also the concentration of radon gas indoor the building were higher from its concentration outdoor the building . And this increase in concentration is due to the fact that the walls of the buildings are considered to be the main source for generating radon indoor the building as well

قياس المواد المشعة الطبيعية المنشا NORM والتراكيز الصناعية للمواد المشعة الطبيعية المنشا TE - NORM في حقل الاحدب النفطي == Natural Occurring Radioactive Materials (NORM) and Technologically Enhanced NORM (TE - NORM) Measurements in AHDEB Oil Field

اسم المؤلف: زينب محمد حسن الزبيدي
اسم المشرف: هادي دويج العتابي | شفيق شاكر شفيق
الموضوع العام: علوم الفيزياء
السنة: 2015
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: واسط
الصفحات الاولى:
المستخلص: The activity concentrations of radium - 226 (226Ra), actinium - 228 (228Ac) and potassium - 40 (40K), which represent the main naturally occurring radioactive material (NORM), were measured in the oil stations of AHDEB oil field in Wassit governorate in Iraq. These activity concentrations were determined using gamma - ray spectroscopy with a hyper - pure germanium (HPGe) and sodium iodide (NaI (Tl)) detectors.The activity concentrations of the obtained data of the crude oil samples were revealed that the overall average specific activity (SA) for 226Ra, 228Ac and 40K were 174.72, 43.46 and 355.07 BqL ⁄. While, the maximum SA values of 226Ra and 228Ac were 212.30 and 52.42 Bq/L for the Crude oil sample taken from the well 32 of the layers of Musharraf oil field, and the maximum SA value of 40K was 465.35 Bq/L for Crude - oil sample taken from the Rumaila layer of the first well. The minimum SA values of 226Ra, 228Ac and 40K were 126.37, 30.59, and 229.98 Bq/L for the Crude oil sample under Hydrostatic pressure.The hazard indices have been calculated in the present work, which include radium equivalent activities (Raeq), gamma dose rate (D), external hazard index (Hex), internal hazard index (Hin), annual effective dose which include indoor and outdoor effective dose rate (E) in units of mSv/y and representative level index (Iγr), respectively. The overall average value of Raeq for the crude oil samples set was 264.21BqL⁄. This value is also considered to be normal (UNSCEAR, 1993). The highest Raeq was 311.01 Bq/L for sample taken from the Rumaila layer of the first well and the minimum value was 187.82 BqL⁄.The overall average value D for the full sample set was found to be 122.52 nGyh⁄. The highest value was 144.51 nGyh⁄ that was higher than the permissible value and the minimum value was 86.97 nGyh⁄.The overall average values of Hex and Hin were 0.7138 and 1.1861, respectively. The highest values of Hex and Hin were 0.8403 and 1.3861 and the minimum values were 0.5075 and 0.8403. The overall average value of Iγr was 1.8361. The highest value was 1.3017 and the minimum value was 2.1687. The overall average values of the Eied and Eoed were 0.259 and 0.0648 mSvy⁄.The highest values of Eied and Eoed in mSvy⁄ were 0.7089 and 0.1772 and the minimum values were 0.4266 and 0.1067.For sludge samples, the obtained data revealed that the average activity concentrations for 226Ra, 228Ac and 40K for these set of samples had the values; 340.1, 90.70 and 491.75 Bqkg⁄, respectively. The maximum activity concentrations of 226Ra, 228Ac and 40K were 573.38, 150.89, and 705.26 Bqkg⁄ appeared and the minimum concentrations were 178.64, 54.13, and 273.32 Bqkg⁄. The average value of Raeq was 507.71 Bqkg ⁄, the maximum value was 843.46 Bqkg⁄ and the minimum value was 277.10 Bqkg⁄. The average value of D for the full sample set was found to be 233.98 nGyh⁄. While the maximum value was 388.01 and the minimum value was 127.55 nGyh⁄. The average values of Hex and Hin were 1.372 and 2.291, respectively. The maximum values of Hex and Hin were 2.279 and 3.829 and the minimum values were 0.749 and 1.231. The average values of the Eied and Eoed were calculated to be 1.148 and 0.287 mSvy⁄. The maximum values of Eied and Eoed were 1.903 and 0.476 mSvy⁄ for SL2 sample, and the minimum values were 0.626 and 0.156 for SL6 sample. The overall average value of Iγr was 0.289, whereas the maximum value was 5.802 and the minimum value was 1.914.For ground water, the obtained data revealed that the average activity concentrations for 226Ra, 228Ac and 40K for these set of samples had the values; 25.05, 7.59 and 35.17 BqL,⁄ respectively. The maximum activity concentrations of 226Ra, 228Ac and 40K were 50.29, 15.24, and 76.94 BqL⁄ and the minimum activity concentrations were 13.70, 4.15, and 8.36 BqL⁄. The average value of Raeq was 38.61 BqL ⁄, the maximum value was 78.01 BqL⁄and the minimum value was 277.10 BqL⁄ for W3 sample. The average value of D was 17.75 nGyh⁄. The maximum value was 35.91 nGyh⁄ and the minimum value was 0.092 nGyh⁄. The average values of the Hex and Hin were 0.10 and 0.172, respectively. The maximum values of Hex and Hin were 0.211 and 0.347 and the minimum values were 0.055 and 0.092. The average values of the Eied and Eoed were 0.087 and 0.022 mSvy⁄, respectively. The maximum value of Eied was 0.176 mSvy⁄ and the minimum value was 0.045 mSvy⁄. Whereas the maximum value of Eoed was 0.044 mSvy⁄ and the minimum value was 0.011 mSvy⁄. The average value of Iγr was 0.226. The maximum value was 0.539 and the minimum value was 0.138.For radon (222Rn) measurements, the overall average values of the measured and calculated parameters were 296.64 Bq/m3, 118.65 Bq/m3, 1.651 WLM, 7.48 mSv/y, and 4490 for radon concentration, equilibrium equivalent 222Rn concentration, working level month, annual Effective Dose, and Excess Lung Cancer per Million Persons per Year (ECL).The background radiation of AHDEB oil field was measured and it is noted that this radiation backgrounds were ranged from 50 to 148 nSv.h - 1 with an overall average value of 80.64 nSv.h - 1.List of contents Title Page

الاستقرارية الفيزيائية - الكيميائية للمتراكبات PVA - MnSO4.H2O مع الظروف الجوية == Physico - Chemical Stability of (PVA - MnSO4.H2O) Composites against weather conditions

اسم المؤلف: زينب كاظم حمزة
اسم المشرف: اسرار عبد المنعم سعيد
الموضوع العام: علوم الفيزياء
السنة: 2015
الموضوع الدقيق: الفيزياء
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: في هذه الدراسه تم تحضير افلام بولي فينيل الكحول وكبريتات المنغنيز المائي باستخدام تقنية الصب مع نسب وزنية مختلفة وهي (2, 5, 10, 15) من كبريتات المنغنيز المائي وقد تم دراسة الخصائص البصريه لها.وقد تضمن هذا العمل ايضا دراسة تاثير الظروف الجوية على الخصائص البصرية لكل النماذج المعرضة.كل النماذج المعرضة وغير معرضة للظروف الجويه شخصت بطرق مختلفة مثل التحليل الطيفي لاشعة تحت الت الحمراء (FTIR)وصور المجهر الضوئي.اظهرت النتائج التجريبية ان طيف الامتصاصيه يزداد بزيادة تركيز كبريتات المنغنيز المائي. فجوة الطاقة تقل بزيادة تركيز الاضافة. وقد تم دراسة الثوابت البصرية الاخرى والتي تشمل (معامل الامتصاص, معامل الخمود, معامل الانكسار, ثابت العزل الحقيقي والخيالي).بعدتعريض النماذج للبولي فينيل الكحول النقي وللمتراكبات (PVA - MnSO4.H2O) وبتراكيز مختلفه وجد ان طيف الامتصاص يزداد بزيادة فترة التعريض. فجوة الطاقه تقل بزيادة فترة التعريض. وقد تم دراسة الثوابت البصريه الاخرى والتي تشمل (معامل الامتصاص, معامل الخمود, معامل الانكسار, ثابت العزل الحقيقي والخيالي).وقد بين طيف (FTIR) عدم وجود تفاعل كيميائي بين المادة المضافة والبوليمر وليس هنالك تكسر بالاواصر الاساسيه لهما بعد التعريض للظروف الجوية, واظهرت صور المجهر الضوئي ان كل النماذج تصبح اكثر خشونة بعد التعريض. | In this study, (PVA - MnSO4.H2O) films are prepared by using casting technique with different concentration of Manganese (II) sulfates monohydrate (2, 5, 10 and 15) wt.% . Also the optical properties is studied, and this work is involved with study the effect of weathering condition of optical properties for all samples which exposure. All the samples that exposure and unexposure to weather conditions have diagnosed by different methods such as fouirer transform infrared spectroscopy (FTIR) and optical microscope images. The experimental results show that the absorption spectrum increased with increasing the concentration of (MnSO4.H2O). The optical energy gap decreasing with increasing of the concentration of the additive. The optical constants (absorption coefficient, extinction coefficient, refractive index, real and imaginary dielectric constants) are studied. After exposure the samples in the form of pure PVA and (PVA - MnSO4.H2O) composites with different concentration found that the absorption spectrum increases with increases exposure time. The optical energy gap decreasing with increasing exposure time. The optical constants (absorption coefficient, extinction coefficient, refractive index, real and imaginary dielectric constants) are studied. The FTIR shows no chemical interaction between the Polymer and the additives and there are no broken fundamental bands after exposure to the weather conditions. Morphological photographs illustrate that the surface of all films become more roughness after exposure.

تصميم وتصنيع الطلاء المضاد للانعكاس معتمدين طريقة الليزر النبضي في الترسيب == DESIGN AND FABRICATION OF ANTI REFLECTION COATING BY PULSED LASER DEPOSITION

اسم المؤلف: زينب حازم عبد الرحيم
اسم المشرف: الاء نزار عبد الغفار | كاظم عبد الواحد عادم
الموضوع العام: علوم الفيزياء
السنة: 2015
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: في هذا العمل تم تصميم طلاء المضاد للانعكاس بسمك ربع ولاربع طول موجي ودراسة خصائص بصرية للاغشية الرقيقة والاستفادة منهما في تصنيع طلاء مضاد للانعكاس ضمن المنطقة المرئية والحمراء القريبة . اعتمد تصميم الطلاء على مفهومين اساسيين هما نظرية المصفوفة المميزة وتصميم طلاء بسمك ليس ربع طول موجي ولحالة السقوط العمودي للضوء.اخذين بنظر الاعتبار ظاهرة التشتت. تم دراسة نفاذية وانعكاسية الطلاء كدالة للتغير في الطول الموجي للضوء الساقط باستخدام الرزمة البرمجية MATLAB. اوضحت نتائج التصميم امكانية الحصول على انعكاسية واطئة لمدى واسع من الطيف الكهرومغناطسي يشمل المنطقة المرئية ومنطقة الحمراء القريبة عندما يكون السمك البصري ضمن المدى اقل 0.7L لمادة MgF2 المرسبة على الزجاج ويكافي الاسماك الهندسية للغشاء (34.5,36.91,78.3) نانومتر, وامكانية الحصول على انعكاسية واطئة لمدى واسع في درجة حرارة التلدين عند سمك البصري 1.2L ويكافى السمك الهندسي ((141.6 نانومتر. تكتسب هذه النتيجة اهميتها في امكانية تخمين السمك الامثل قبل البدء بمرحلة التحضير حيث اشارت النتائج الى معادلة تجريبية تربط بين عدد النبضات وسمك الغشاء. لغرض تصنيع الطلاءالبصري, تم استخدام طريقة الترسيب بالليزر النبضي لليزر النيديميوم - ياك1064 نانومتر الذي يعامل بتقنية التولد المتوافق الثاني بطول موجي 532 نانومتر والذي يعمل بتقنية عامل النوعية بمعدل تكرارية (1 - 6) هرتز وامد نبضة 10 نانوثانية. لتحضير اغشية فلوريد المغنيسيوم المرسبة على الزجاج, قمنا بدراسة ظروف التحضير التي تتضمن التغير بعدد النبضات (150و250 و350و 450 نبضة) لترسيب اغشية فلوريد المغنيسيوم ومدى تاثيرهم على سمك الاغشية المحضرة وتركيبها وحجم الحبيبات وبالتالي على نفاذيته ومدى امكانية استخدامه كطلاء مضاد للانعكاس. لقياس سمك الاغشية المحضرة, تم استخدام جهاز مقياس اللبسومتر وتم استخدام جهاز المطياف لايجاد النفاذية والانعكاسية والثوابت البصرية ومعاملي الانكسار والتوهين (n, k) وعلى التوالي. اوضحت النتائج بان الطلاء المضاد للانعكاس المحضر من طبقة واحدة يمتلك نفاذية عالية وانعكاسية واطئة تشمل منطقتين من الطيف المرئية والحمراء القريبة وان معامل الانكسار يتراوح بين (1.05 - 1.25( في حين كانت اسماك الاغشية المحضره تتراوح بين )34.5 - 141.6 ) نانومتر, كذلك اوضحت صور (AFM) بان الحجم الحبيبي يتراوح ضمن المدى (86.55 - 94.81) نانومتر. | In this work design and fabricated antireflection coating (AR’C) with single layer. Design of the AR’C was based on the characteristic matrix method with quarter and non - quarter optical thickness. The effect of deposited material at normal incident of light was taken into account and the reflection performance was computed with the aid of MATLAB over the visible and near infrared region. Results show that wideband AR’C was achieved when deposited thin film of MgF2 on glass with non - quarter optical thickness less 0.7L related to geometrical thickness (34.5,36.9,78.3 nm) at room temperature. Also wideband AR’C achieved with non quarter 1.2L optical thickness deposited related to geometrical thickness (141.6nm) at annealing temperature. However results accept significant importance to estimate the optimum thickness before preparation stage. In this study antireflection coating fabricated by using pulsed laser deposition technique (PLD) which deposit MgF2film on glass substrate. Q - switching Nd : YAG laser beam with second harmonic generation (SHG) technique of wavelength 1064 nm and 532 nm, repetition rate 1 - 6 Hz and the pulse duration 10 ns was used. The film thickness, structural behavior and grain size dependent on that prepared conditions which include variation number of shot (150,250,350,450 pulses) have been studied.The thicknesses of MgF2 nanostructure films were measured using Lipsometre. Further, the experimental results shows high transmittance, wideband low reflection and the refractive index within the range (1.05 - 1.25), while the thicknesses are (34.5 - 141.6 nm). Atomic force microscope (AFM) image illustrate that the grain size of the film within the range (86.55 - 94.81) nm

تحضير ودراسة الخصائص الامتصاصية لاكاسيد الفيرايت باستخدام طريقة السيراميك == Preparation and Study the Absorption Properties of Ferrite Oxides using Ceramic Method

اسم المؤلف: زياد طارق اسماعيل العبوسي
اسم المشرف: كاظم جواد كاظم الشجيري
الموضوع العام: علوم الفيزياء
السنة: 2014
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: Compounds of ferrimagnetic materials were prepared in this work in order to investigate and evaluate the microwaves absorption at X - band with the range of frequencies (8 - 12.5 GHz) and Ku - band with the range of frequencies (12.5 - 18 GHz). And the second band is used for the first time in Iraq.Conventional Ceramic techniques (the solid state reaction method) were used to prepare three compounds of spinel ferrite : Cu - Zn ferrite, with formula (Cu1 - xZnxFe2O4), Mg - Zn ferrite, with formula (Mg1 - xZnxFe2O4), and Ni - Zn ferrite, with formula (Ni1 - xZnxFe2O4) at values of x = (0.0, 0.1, 0.3, 0.4, 0.5, 0.6), where x is the proportion of zinc in the ferrite, as bulk (54) samples of rectangle in dimensions (22.6*10*10 mm) within in X - band refine it to make its dimensions (15.5× 7.5×10) mm within in the Ku - band.The resonance peaks of three types of spinel ferrite appeared at the frequencies (9, 10, 11, 14, 15, 16, 17) GHz, and these peaks remain at the same frequencies with a different thickness for all types of ferrite, this indicates that the peaks are not related to thickness.For all samples it was found that the effect of increase the thickness and sintering temperature increased the values of attenuation and absorbance. And the best values of the absorbency were in the range of (Ku - band).The value of total transmission and the absorbance is 100% for sample of (Ni0.9Zn0.1Fe2O4) were the best values at (1050) °C then (14) GHz.The best results were obtained in this research, and the best values of absorbance and stability are (CuFe204, Cu0.9Zn0.1Fe2O4, Cu0.9Zn0.1Fe2O4,Cu0.4Zn0.6Fe2O4) that had been burned by (1000, 1050, 1100, 1050) respectively. These samples were range of (Ku - band).The best result was similarity in behaviour of absorbance for the sample (Mg0.6Zn0.4Fe2O4) at the range (X - band).X - ray diffraction results showed that the structure was polycrystalline for all samples and for all (X) values.The density of samples greatly depends on the temperature of sintering, witch increases proportionally with the temperature of the sintering

تحضير درع متعدد الطبقات وحساب عامل التراكم باستخدام انواع مختلفة مم البوليمرات == Multilayered Shielding Preparation and Buildup Factor Calculation Using Different Type of Polymers

اسم المؤلف: زهير سالم خميس
اسم المشرف: محمد قاسم الفخار | حارث ابراهيم جعفر
الموضوع العام: علوم الفيزياء
السنة: 2015
الموضوع الدقيق: الفيزياء
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: واسط
الصفحات الاولى:
المستخلص: Due to the possibility of producing secondary radiation when a radiation is being attenuated by a certain type of radiation shield, the use of multilayer shielding appears very useful. This study aims to investigate the use of multilayer materials as nuclear radiation shielding.The work presented in this thesis focuses on the possibility of using polymer materials as a nuclear shield. This polymer (high density polyethylene and epoxy) is chosen due to different reasons among which are its local availability, the ease of mixing additives with it, light weight, and flexibility. The polymer as a single shield was investigated, where five different forms of the polymer were used as a single shield. These kind of shield are polymer (High Density Polyethylene HDPE, and Epoxy) alone, HDPE with a 38%by weight of Pb (as an additive), Epoxy with a 33%by weight of Pb, and Epoxy with a 33% by weight of Al (as an additive). The attenuation coefficient (μ), and buildup factor (B) were measured for all five forms and composition. In particular, the attenuation coefficients were found to increase with the increasing of the Pb or Al additive and decrease with gamma rays energy increase, while the buildup factor where decrease with the increase of the Pb or Al additive and increase with the increasing of energy.On the other hands, the multilayer shielding materials were chosen to be either Al or Pb slides (with different thickness) with a slide of 2.8cm of polymer (HDPE or Epoxy) in different repeated combinations. In order to evaluate the values of μ and B for this multilayer composition, the values of μ and B for each Pb and Al were evaluated. Then these two values were estimated for the different combinations of the multilayer shields. In particular, it was found that placing the low Z material (polymer) in front of the detector [NaI(Tl) detector] first and then high Z material before that

تصنيع ودراسة خواص معدن - فثالوسيانين العضويه كمتحسس حرارة == Fabrication and Study Properties of Organic Metal - Phthalocyanine as Temperature Sensor

اسم المؤلف: رؤى مثنى علي
اسم المشرف: ندى خضير عباس
الموضوع العام: علوم الفيزياء
السنة: 2016
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: Copper Phthalocyanine tetrasulfonic acid tetrasodium salt (CuPcTs) thin films with different annealing temperatures (100, 150 and 200)oC have been prepared by spin coating technique on glass & ITO substrate with speed rate of 1000 rpm for 1 min, the obtain films have 100±5 nm thickness. This dissertation deals with different measurement techniques (Thermal, Structure, Morphological, Optical and Electrical measurements) in order to investigate the optimum condition to fabricate sensor device.The structures of CuPcTs thin films which deposited on glass substrate have been studied by X - ray diffraction (XRD), Atomic Force Microscope (AFM) and (FESEM) techniques, XRD studies show that thin films have polycrystalline structure for all annealing emperatures with perfect orientation (001). Also the surface morphology by AFM measurement for CuPcTs thin films has been studied; it shows that all films after heat treatment go to Nano size. The roughness decreases with increasing temperatures, and by (EDX) technique the elemental ratios of thin films are determined.The optical measurement showed that the as - deposited and annealed films have two peaks which are (B, Q1and Q2) bands, B in Ultra Violet region attributed to transition between d level for Cu metal and π* in LUMO, and Q bands in Visible region attributed to the transition between π(HOMO) - π* (LUMO). These measurements demonstrated that the energy gap of CuPcTs depends on the annealing temperatures, the photoluminescence spectra (PL) showed the traps inside energy gap play an important role and effect onoptical behavior. It’s studied to confirm the results of optical band gap, FTIR spectra give results about the bonds of (CuPcTs) and its position compared with H2Pc as a reference. The electrical properties of these films were studied with differentannealing temperature. Hall measurements showed by increasing thin films temperature the conductivity decreased at 100oC then it increase at 150oC finally it returned to decrease that may be due to phase transitions, all the films are p - type.CuPcTs Capacitive - Resistive surface type temperature device sensor has been fabricated by using two electrodes (Aluminum and Silver), the capacitive response of this sensor was observed by Raising the temperature gradually.Capacitive - Resistive temperature sensor showed that the response to variation of temperature in range (RT - 200)0C and the response time ≈ 20±5 Sec. for two electrodes, The fabricated sensor appear enough sensitivity and good response and recovery times and strong affected by frequency variation.Practical experience has shown results that aluminum electrode has capacitance and resistance higher than the silver electrode depending on the different frequencies values, while the silver electrode has the shortest response time.

تقييم المقاطع العرضية لليورانيوم للتفاعلات المستحثة بالنيوترون == Cross Sections Evaluation of Uranium for Neutron Induced Reactions

اسم المؤلف: روناك اكرام علي
اسم المشرف: ايمان طارق العلوي
الموضوع العام: علوم الفيزياء
السنة: 2015
الموضوع الدقيق: الفيزياء
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: لقد تم في هذا البحث حساب قيم المقاطع العرضية لنظائر اليورانيوم (A=230 - 238) للتفاعلات المستحثة بالنيوترونات التالية ,,,(n,f), (n,tot), (n,el), (n,inl), (n,2n), (n,3n), (n,γ), (n,p), (n,t), (n,d), (n,α), (n,2α),and (n,2p)المقاسة بفترات مختلفة من الطاقة حيث ان هذه القراءات تم اخذها من الوكالة الدولية للطاقة الذرية (IAEA ) ومن المكتبات المشهورة عالميا مثل EXFOR, CINDA, ENDF, JEFF, JENDL,ROSFOND,CENDL,WIND, TENDL, BROND, IRDF, EAF وقد تم قياسها في الفترة الاولى من منتصف القرن الماضي وحتى اخر سنوات الماضية .لقد تم تحليل المديات الكاملة للطاقة لكل تفاعل وقد تم اعادة حساب وتقييم المقاطع العرضية ضمن فترات صغيرة مختلفة حسب مديات الطاقة للنيوترون القاصف مع الاخطاء المرافقة لها. قد تم وضع صيغ رياضية لمتعددة الحدود في معظم التفاعلات والتي تربط بين تغيير المقطع العرضي مع الطاقة والتي يمكن استخدامها للتنبىء بقيم المقاطع العرضية غير المحسوبة. لقد تم حساب قيمة Q - للتفاعل وطاقة الربط وطاقة العتبة وفرق الكتلة وعامل الرص لكل تفاعل ولكل عنصر هدف. ان التقييمات اعتمدت بشكل رئيسي على حسابات نموذج الجهد البصري لقد اعتمدت الحسابات على معاملات الجهد البصري النووي حيث تم اختيار وجمع المعلومات من مكتبة (RIPL) التابعة للوكالة الدولية للطاقة الذرية. لقد قمنا بدراسة صيغتين مختلفتين لنموذج الجهد البصري حيث ان الصيغة الاولى تسمى نموذج الجهد البصري القياسي والمعاملات ماخوذة من مكتبة Beijing والصيغة الثانية لنموذج الجهد البصري قد تم حسابها بتحديد ثلاث مديات طاقية. لقد قمنا بدراسة نسبة التفاعل (n,f) لكل نظير من نظائر اليورانيوم نسبة الى يورانيوم - 235 والذي يعتبر نموذج قياسي. لقد قمنا بحساب هذه النسبة لجميع التفاعلات المتوفرة لدينا وليس فقط تفاعل الانشطار واحتسبناها نسبة الى يورانيوم - 235.حساب اخر تم اضافته الى هذه الدراسة وهو دراسة تاثير التلوث لوليدة اليورانيوم - 237 والتي هي نبتونيوم - 237 بعمر نصفي 6.8 يوم وكذلك حساب الفيض النيوتروني لكل منهما. | The cross sections of Uranium isotopes (A=230 - 238) for the (n,f), (n,tot), (n,el), (n,inl), (n,2n), (n,3n), (n,γ), (n,p), (n,t), (n,d), (n,α), (n,2α),and (n,2p) reactions are calculated with different energy intervals which are collected from International Atomic Energy Agency (IAEA). The available cross sections data for the reactions mentioned above are collected from the well known international libraries like EXFOR, CINDA, ENDF, JEFF, JENDL, ROSFOND, CENDL, WIND, TENDL, BROND, IRDF, EAF and measured during the period from the middle of the last century up to several years ago.The cross sections are reproduced in fine steps of incident neutron energy in different intervals with the corresponding errors. The recommended cross sections for all available experimental data have been calculated for all considered reactions mathematical representative equations for all these reactions are formulated. These equations represent the variation of the cross section with energy, which could be used to predict the values of uncalculated cross sections.Q - value, threshold energy, binding energy, mass excess, and packing fraction for each reaction and target element have been also calculated.The evaluations are based mainly on the calculations of the optical model potential. The calculations are based on the nuclear optical potential, where the relevant parameters are collected and selected from Reference Input Parameter Library (RIPL) which is being developed under the international project coordinated by the International Atomic Energy Agency (IAEA). We study two different formula for optical model potential the first formula is the standard optical potential model and its parameters are taken from Beijing library. The second formula is the optical potential with different energy ranges. We study the ratio of the (n,f) cross sections for each Uranium isotopes relative to (n,f) cross section for U - 235 which could be considered as a standard sample. We have done the ratio not for the (n,f) cross sections only but also for other reactions like ,(n,f), (n,tot), (n,el), (n,inl), (n,2n), (n,3n), and (n,γ) relative to U - 235 reactions cross sections.Another evaluation is added to cross sections is the effect of the contamination of the daughter of U - 237 which the daughter is Np - 237 6.8day and their relative flux

دراسة تاثير المعاملة الحرارية على الخواص التركيبية والميكانيكية لبوليمر (بولي تيترافلورواثيلين) == Study the Effect of Heat Treatment on the Structural and Mechanical Properties for poly (tetrafluoroethylene

اسم المؤلف: رند باسم لطفي الكرخي
اسم المشرف: مي عبد الستار محمد نجيب
الموضوع العام: علوم الفيزياء
السنة: 2015
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: درس في هذا العمل نوعين من بولي تيترافلورواثيلين ( النقيين ولكن باختلاف الشركة المصنعة PTFE) (صيني _اماراتي ) بطريقه صب المحلول كافلام رقيقه واشرطة , بواسطه الخواص التركيبيه (حيود الاشعه السينيه ومسعريه المسح التفاضلي ) والخصائص الميكانيكية بدلاله درجات حراره مختلفة للدوره الحرارية . يبين كلا النوعين تغير في الشده المستطاره من المستوى القاعدي (100) عند تغير درجه حرارة الدورة الحرارية واظهر النوعين زيادة في التبلورية مع زياة درجة الحرارة .كذلك اختلاف في الانثالبي عند اختلاف درجات الحرارة حيث لوحظ زياة الانثالبي بزيادة درجة الحرارة واختلاف في الخصائص الميكانيكيه ( الاجهاد والانفعال عند نقطة الخضوع ونقطه الكسر ومعامل يونك) للبوليمر حيث اظهرت المعالجة الحرارية للبوليمر بدرجات حرارة مختلفة من اجل معرفة خصائصه ومقاومته الى الظروف البيئية ان الخواص الميكانيكية تزداد زيادة خطيا مع زيادة درجة الحرارة .لوحظ بان انتاج الشركه المصنعة الصينية افضل من ناحية النتائج لايجاد درجة التبلورية والخصائص الميكانيكيه عن انتاج الشركة المصنعة الاماراتية لنفس المادة البوليمرية | In this study two modifications of pure polytetrafluoroethylene (PTFE) [C2F4]n. China_UAE source prepared from solution cast as film and strip have been studied by structural (X - ray diffraction (XRD), Differential Scanning Calorimetry (DSC)) and mechanical properties .subjected to different temperature heating cycle. Both modifications show variation in the scattered X - ray intensity of the basal plane (100) as the temperature of heating cycle is changed and show increasing in crystallinity with the increase of temperature .Moreover, the Enthalpy of each kind is changed with difference of heat treatment where the enthalpy increase with the increase of temperature, and two modifications show different in mechanical properties for PTFE (young's modulus, stress at break, stress at yield, elongation at yield. And elongation at break) when the temperature is change ,The heat treatment of polymer to different temperatures in order to know its properties and resistance to environmental conditions results showed that the mechanical properties increase linearly with the increase of temperature.It seems that the product company of china is better than the product company of UAE in degree of crystallinity and mechanical properties for this polymer.

الدراسه النظريه لتصميم ماكنه بؤره البلازما وتحقيق العوامل المختلفه التي تؤثر على حصيله النيترون المنبعث == Theoretical study to design plasma focus machine and investigate various parameters that affect its emitted neutron yield

اسم المؤلف: رنا عيســـى بــك مــــراد
اسم المشرف: مصطفى كامل جاسم | رعد حميد مجيد
الموضوع العام: علوم الفيزياء
السنة: 2014
الموضوع الدقيق: فيزياء البلازما
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: في هذا البحث تم تصميم جهاز بؤرة البلازما الكثيفة نظريا بالاعتماد على موديل (لـــي) بناءا المعادلات الرياضية لنموذج لي لكل من هندسة القطبين وعناصر الدائرة الخارجية التي تضم متسعة ومحاثة ومقاومة (RLC). وبعد اجراء الحسابات اللازمة تم ادخال نتائج التصميم في برنامج لرؤية مدى امكانية تشغيله نظريا من خلال دراسة المعلمات المختلفة التي يوفرها البرنامج وبالتالي التعرف على ظروف تشغيله والعوامل المؤثرة عليه. لقد اختير غار الديترويوم كغاز عامل في هذه المنظومة للحصول على ناتج نيتروني من اجل التفاعل النووي الاندماجي. وتم اختبار ودراسة المنظومة عند ضغطين مختلفين (3و4 تور) حيث درست مختلف معلماتها التي يوفرها البرنامج ونوقشت وقورنت النتائج بالاشكال البيانية. اضافة لذلك تمت مقارنة المنظومة المصممة مع منظومة قياسية تناظرها من حيث التركيب النظري وهي منظومة NX2 التي بنيت اساسا للحصول على الاشعة السينية باستعمال غازات النبيلة. اختير في البحث ان يكون غاز الديتريوم هو الغاز العامل للحصول على ناتج نيتروني من اجل المقارنة، حيث درست جميع معلمات التشغيل للمنظومة المصممة مع القياسية بالرسوم البيانية.لقد وجد من خلال انجاز الحسابات اللازمة بان الشكل البياني لانحدار تيار الانبوب الكلي (dip) مباشرة بعد قمة التيار مع الزمن للمنظومة المصممة متفق تماما مع الشكل العام المميز لمنظومات بؤرة البلازما التجريبية دلالة على ان حسابات التصميم صالحة لهذه المنظومة وبالتالي يمكن اجراء الحسابات. ان تصرف فولتية الانبوب مع الزمن للمنظومة المصصمة كان بنفس الشاكله مع المنظومة القياسية. وينطبق هذا على سلوك المعلمات الاخرى بين المنظومتين مثل السرعة والمسار المحوريان والمسار الى الداخل للصدمة الشعاعية ومسار وسرعة استطالة القرص ومسار وسرعة الصدمة المنعكسة شعاعيا وغيرها.تم دراسة ومقارنة تغيرات درجة حرارة البلازما مع الزمن للمنظومتين عند نفس الضغط ولضغطان مختلفان للمنظومة المصممة وكان تصرف ماكنتا بؤرة البلازما بنفس الطريقة. وتم حساب الخسائر المتولدة من الماكنتان مثل خسائر جول وبرمنشتهالنك واعادة الاتحاد وخسائر الطاقة الشعاع الخطي مع الزمن. اخيرا وجد ان المنظومة المصممة ( 1.66 × neutron per shot ) توفر ناتج نيتروني اكبر من المنظومة القياسية (5.15 × neutron per shot) . لقد تصرفت المنظومة المصممة مثل المنظومة القياسية لكن كان الاختلاف في سلوك المنظومة المصممة والقياسية هو اختلاف الترتيب الهندسي للمنظومتين من حيث هندسة الاقطاب واختلاف قيم العناصر الكهربائية للدائرة الخارجية. ان المنظومة المصممة نظريا في هذا البحث يمكن ان تكون مشروع لبناء ماكنة بؤرة بلازما تطبيقية للحصول على ناتجها النيتروني العالي للاستفادة منه في اجراء تفاعل الاندماج النووي.

تصنيع ودراسة خصائص كاشف المفرق الهجين Cdo/ Si المشاب والمحضر بطريقة الرش الكيميائي الحراري == Fabrication &Characterization Heterojunction Photodetector of Cdo/ Si by Spray Pyrolysis Technique

اسم المؤلف: رفل صالح ساجت فياض
اسم المشرف: سعاد غفوري خليل العاني | رائد عبد الوهاب اسماعيل
الموضوع العام: علوم الفيزياء
السنة: 2015
الدرجة: ماجستير
الجامعة: جامعة بغداد
اللغة: العربية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: تم في هذا البحث تصنيع ودراسة خصائص كاشف المفرق الهجين نوع CdO/p - Si المشوب اذ حضرت اغشية اوكسيد الكادميوم(CdO) بطريقة الرش الكيميائي الحراري وبدرجة حرارة قاعدة ثابتة 380o C) ) وبالتراكيز المولارية M(0.1, 0.15, 0.2, 0.25) وشوبت بعنصري النحاس والالمنيوم بنسب (0.5%, 1%, 3%, 5%) على الزجاج وعلى شرائح من السليكون احادية التبلور (Single Crystal) من نوع p - type ذات اتجاهية بلورية (100) ومقاومية كهربائية (2 - 20 Ω.cm) ومن نوع n - type ذات اتجاهية بلورية(100) ومقاومية كهربائية (10 Ω.cm) وسمك يتراوح بين (400 - 600 nm) .ودرست الخواص التركيبية والطوبوغرافية والبصرية والكهربائية لغشاء CdO بتغير التركيز المولاري وبثبوت درجة حرارة القاعدة (Ts) لقد اوضحت نتائج حيود الاشعة السينية ان اغشية CdO ذات تركيب بلوري مكعب وان اعلى شدة كانت عند المستوي (111) , اوضحت النتائج البصرية ان قيم فجوة الطاقة تعتمد بشكل كبير على التركيز المولاري اذ وجدت ان قيم فجوة الطاقة لغشاء CdO النقي كانت تتراوح مابين 2.61 eV الى 2.34 eV ولوحظ ان فجوة الطاقة تبدا بالنقصان مع زيادة التشويب بالالمنيوم والنحاس مقارنة مع اغشية CdO النقية . حيث ان فجوة الطاقة عند التشويب بالنحاس كانت تتراوح مابين 2.5 eVالى 2.31 eV وتتراوح مابين 2.62 eV الى 2.48 eV عند التشويب بالالمنيوم.اوضحت نتائج قياس تيار - جهد للكاشف الضوئي ان مقدار عامل المثالية (Ideality factor) للكواشف المحضرة بمولارية وتراكيز اشابة مختلفة يزداد مع زيادة التركيز المولاري وان افضل قيمة له كانت بحدود 1.7 عند تركيز 0.5% وبالنسبة لشوائب النحاس وبحدود 1.8 بالنسبة لشوائب الالمنيوم بتركيز 0.5% .اظهرت نتائج قياسات الاستجابية الطيفية ان الكواشف المصنعة تعمل ضمن المنطقة الطيفية (400 - 850nm) ووجود قمتين لكاشف (CdO/Si) المشوب وغير المشوب الاولى تقع عند الطول الموجي (550 nm) والتي تعود الى غشاء CdO والثانية عند الطول الموجي (800 nm) والتي تعود الى السليكون. لقد اوضحت نتائج الاستجابية الطيفية للضوء الابيض ان الكواشف تمتلك خصائص خطية جيدة ولاوجود لمنطقة اشباع وان هذه الخصائص تحسنت بعد الاشابة.تم حساب الكشفية النوعية للكواشف المصنعة ووجد انها تتغير مع ظروف التحضير حيث ان اعلى قيمة لها كانت بحدود 6*1011(HZ1/2.W - 1.cm) عند الطول الموجي 500nm وبلغت 7*1011(HZ1/2.W - 1.cm) عند الطول الموجي 700nm للكاشف المصنع CdO : Al/Si المشوب بتركيز 5% . | We discussed in this research Manufacturing and study the detector hybrid retail properties type CdO/ P - Si the doping ,If film were prepared the Cadmium Oxide (CdO), by the way chemical spraying with tempratuer the constant base (380oC) And molar concentrations (0.1, 0.15,0.2,0.25)M. It was the doping for two element Copper and Aluminum with percentages (0.5%, 1%, 3%, 5%) on the glass and the slides of Silicon crystallization single from p - type With crystalline directional (100) and Electrical resistivity (2 - 20 Ω .cm) and from N - type With crystalline directional (100) and Electrical resistivity (10 Ω .cm) at thickness between (400 - 600 nm).We study the Characteristics Synthetic and Optical and Electrical the film CdO , by change molar concentrations with tempratuer the constant base (Ts) , I have explained the results X - ray diffraction that film CdO With a cubic crystalline structure And that the highest intensity was at the level of (111), The results showed of optical that value Energy gap the large dependent on molar concentrations , It was found the value Energy gap they were between (2.34 ev - 2.61 ev) and It was found simpel change in Energy gap when the doping by Copper they were between (2.31 ev - 2,51 ev) and Improving Energy gap when the doping by Alminum they were between (2.48 ev - 2.62 ev).The results measure Current - Potential the optical detector there Ideality factor the detector Prepared with tempratuer the constant base and different molar concentrations where the value increases with molar concentrations decreases, and the better value they were limited 1.7 when concentration 0.5% for Impurities Copper , And limited 1.8 for Impurities Alminum when concentration 0.5%.The result measure Responsive spectral the detector Manufacture the work with in Spectral region (400 - 850 nm) , And found two value the detector (CdO/ Si) the doping and undoping , The first located when wevelength (550 nm ), which return to the detector CdO , The second when wevelength (800 nm ), which return to the detector Silicon. It was found the value Specifc Detectvity the showed the better value they were the detector CdO : Al/ Si the doping concentration 5% it was about 6*1011(HZ1/2.W - 1.cm) at the Wavelength (500nm) and 7*1011(HZ1/2.W - 1.cm) at the Wavelength (700nm).I have explained the results Responsive spectral for white light that the detector has liner properties and this properties improving after at dopend.

المقاطع العرضية لتفاعلات القنص والجسيمات المشحونة لانتاج نظائر اليود الطبي المشع == Capture and Charged Particles Reactions Cross Sections for Production of Iodine Medical Radioisotopes

اسم المؤلف: رغد سعدون محمد
اسم المشرف: ايمان طارق العلوي
الموضوع العام: علوم الفيزياء
السنة: 2014
الدرجة: ماجستير
اللغة: الانكليزية
مكان الجامعة: بغداد
الصفحات الاولى:
المستخلص: تعددت الوسائل التي يحاول الاطباء من خلالها الكشف المبكر عن الامراض السرطانية ومن ثم السيطرة عليها قبل ان تتفاقم ويصعب علاجها. ان اخر ما توصل اليه الطب الحديث للحد من انتشار هذه الامراض هو استخدام نظائر المواد المشعة في علاج بعض الامراض وتشخيص البعض الاخر حيث يلعب النشاط الاشعاعي المنبعث من انحلال النظائر المشعة مثل انبعاث الكترونات اوجر والبوزترونات واشعة كاما دورا هاما في التطبيقات الطبية التشخيصية والعلاجية, ان الانوية المشعة ذات الاعمار النصفية الصغيرة (بضع ساعات) تكون ملائمة للحالات التشخيصة وهذا مايسمى التصوير بواسطة الانبعاث البوزتروني (PET) او بقياس طاقة فوتون كاما المنفرد (SPET) حيث تعطي هذه التقنيات صور ثلاثية الابعاد للعضو المراد فحصه, اما الحالات العلاجية فان الاشعة المؤينة المنطلقة لمسافات قصيرة تكون ملائمة لاختراق الانسجة وتغير تركيب الحمض النووي للانسجة المصابة. هذه النظائر يتم انتاجها بواسطة معجلات او مفاعلات نووية خاصة لهذه الاغراض ومن ثم يتم التاكد من نقائها من الشوائب النووية التي تظهر في عملية الانتاج قبل اعطائها للمريض . مما تقدم تم اختيار نظائر اليود المشع (I; A= 119→126, 128, 130, 131) في هذه الدراسة لان معظم نظائره ذات اعمار نصفية ملائمة للحالات العلاجية والتشخيصية. ان الطرق الرئيسية لانتاج اليود هو باستخدام الاهداف , , والتي تضمنت 38 تفاعل مباشر و9 تفاعلات غير مباشرة. وقد تم حساب المقاطع العرضية لتفاعلات (p,γ)و (p,α)و(p,xn) و(d,xn) و(α,xn) لانتاج نظائر اليود المشع حيث تم تقييمها في العمل الحالي اعتمادا على القيم العملية المتوفرة في مكتبة (EXFOR) التابعة لوكالة الطاقة الذرية الدولية (IAEA) حيث احتوت مكتبة (EXFOR) على البيانات العملية للمقاطع العرضية المقاسة لعدة سنوات سابقة ولعدة باحثين حتى الوقت الحالي. ان افضل التفاعلات لانتاج I - 123 هما و, وكذلك افضل التفاعلات لانتاج I - 124 هما و, ولانتاج I - 125 فان افضل تفاعل هو كون هذه التفاعلات تتمتع بانتاج عالي وشوائب قليلة ضمن مدى طاقي قليل. وان افضل تفاعل لانتاج I - 131 هو التفاعل غير المباشر لاهميته باستخدامه في (SPET) لغرض تصوير الغدة الدرقية وكذلك لعلاج سرطان الغدة الدرقية. لقد تم تحليل مديات الطاقة الكاملة لكل تفاعل وقد تم اعادة حساب المقاطع العرضية بفترات صغيرة لطاقة البروتون او الديتريون او جسيمة الفا الساقط بلغت (0.01MeV) مع الاخطاء المرافقة لها. وبذالك تم حساب المقاطع العرضية المختارة لانتاج نظائر اليود المشع وايجاد معادلات الملائمة من نوع Polynomials لعدة مراتب n= 4→10 والتي تربط بين تغير المقطع العرضي مع الطاقة والتي يمكن استخدامها للتنبؤ بقيم المقاطع العرضية غير المحسوبة. لقد تم حساب مستوى الشوائب التي تظهر في عمليات انتاج النظائر التي لها اعلى تطبيقات طبية واختيار افضل منطقة ذات مدى طاقة يتم تحديده باستخدام السايكترون للحد من ظهور الشوائب النووية وتم الحصول على توافق جيد بين النتائج النظرية والنتائج العملية المتوفرة. لقد تم حساب قدرة الايقاف على اساس صيغة زكلر من اجل حساب ناتج (yield) كل تفاعل وحساب سمك الهدف. وقد تم حساب قيمة Q وطاقة العتبة وطاقة الربط والمقاطع العرضية لنظائر اليود المختارة. تم بناء البرامج الحسابية Recom.m وStopp.m وStopd.m وStopa.m وYield.m وImpurity.m في العمل الحالي باستخدام Matlab - 8 اضافة لاستخدام برنامج SRIM (2003) لاجراء الحسابات. | There are many ways in which doctors attempt to early detection of cancer and then control it before it worsen and becomes difficult to treat. The latest findings of modern medicine to reduce the spread of these diseases is the use of isotopes of radioactive Iodine in the treatment of some diseases and diagnosis of others where it plays radioactivity emitted from the dissolution of radioactive isotopes, such as the emission of Auger electrons, positrons and gamma rays which play an important role in medical applications of diagnostic and therapeutic. The half - life of radioactive nuclei with a few hours are appropriate for situations diagnostic and this called imaging by Positron Emission Tomography (PET) or Single Photon Emission Tomography (SPET). These techniques give a three - dimensional picture of the organ to be scan, either cases the therapeutic ionizing radiation emitted over short distances are appropriate to penetrate the tissue and change the structure of DNA of the infected tissue. These principals are produced by accelerators or nuclear reactors, especially for this purpose and then be sure of the purity of nuclear impurities that appear in the production process before giving it to the patient. Isotopes of radioactive Iodine (I; A= 119→126, 128, 130, 131) have been selected in the present work. Since they have suitable half - life that could be used for treatment and diagnostic. The main production routes, use , , targets, including 38 direct reactions and 9 indirect reactions. Exciitation functions for proton, deuteron and alpha particles for the reactions (p,xn), (p,α), (p,γ), (d,xn), (α,xn) (n,p) for the production of isotopes of radioactive Iodine have been evaluated using an experimental of energy of incident particles and cross sections published in the International Atomic Energy Agency (IAEA), especially (EXFOR) library which measured cross sections for different authors and for several years prior to the present. The best reactions for the production of Iodine - 123 are the reaction and reactions, while the best reactions for the production of Iodine - 124 are and reactions. For the production of Iodine - 125, the best reaction is , because it possesses less impurities and low energy ranges and higher yields. While the best indirect reaction for the production of Iodine - 131 is for its importance using in (SPET) for imaging of the thyroid gland and as a therapy by thyroid cancer. The analysis of a complete energy range has been done for each interaction. The cross sections are reproduced in fine steps of incident proton or deuteron or alpha particle energy in 0.01MeV intervals with their corresponding error. Therefore, the selected cross section for the production of radioactive Iodine isotopes have been calculated with a polynomials fitting with a degree n=4→10 that could be used for the prediction of un calculated cross sections. Level of impurities that appear in the isotope production processes that which have the highest medical applications have been calculated. The best area of useful energy range has been chosen by using cyclotron to reduce the appearance of nuclear impurities The stopping power according to Zeigler formulae was used in order to obtain the yield for each reaction and to calculate the target thicknes. Q - value, threshold energy and binding energy for selected Iodine isotopes were also calculated. The programmes of Recom.m, Stopp.m, Stopd.m, Stopa.m, Yield.m and Impurity.m, have been built in the present work using Matlab - 8 to calculate the results of the present work, as well as SRIM (2003) program were used
1 ... 112 113 114 115 116 ... 187